2002 Dodge Dakota Slt Extended Cab 4 Door on 2040-cars

Auto blog

Dodge Charger Hellcat makes 1,032 hp with Hennessey help

Sometimes you just want four doors. Earlier this week we brought you Hennessey's riff on the Dodge Challenger Hellcat. Now comes the Charger. Much like its two-door sibling, the Charger gets boosted to as much as 1,032 hp and 987 lb-ft of torque (at the crank) thanks to the addition of a twin-turbocharging setup that works with the factory supercharger. The turbo headers and downpipes are stainless steel, and there is a high-flow air-to-water intercooler and dual-turbo waste gates. Hennessey also beefs up the fuel injectors, fuel pump, and the rest of the fuel system. The engine management system and chassis are recalibrated to accommodate all of this. You also get numbered plaques signed by John Hennessey, the boss of the Texas tuning outfit, and the technician who does your build. Hennessey's additions result in zero-to-60 mph sprints in 2.7 seconds, and the big sedan can run the quarter mile in 9.9 seconds at 142 mph. Like the Challenger, the Charger has the same disclaimer: the lofty horsepower figure comes from an engine dyno, and it will be a 15-to 20-percent lower at the rear wheels. Related Video: Image Credit: Hennessey Performance Dodge Performance Sedan Hennessey dodge charger hellcat

2020 Dodge Challenger Drag Pak will debut at SEMA

Mopar fans have countless reasons to get hyped about the 2019 SEMA show. Speedkore is bringing a twin-turbocharged, all-wheel-drive Dodge Charger Hellcat Widebody, Mopar is bringing a done-up 1968 Dodge D200 "Lowliner," Ram is bringing a diesel 1500 overlander, and Jeep is bringing a custom off-road Wrangler. But the launch of the new 2020 Dodge Challenger Drag Pak might garner the most attention from the brand's most serious customers. Prior to the show, Mopar teased a photo and a short video clip, both showing a new Dodge Challenger from the overhead view. The white Challenger showed a wide blue stripe down the center of the car with two pinstripes along each side. "Powered by SRT" runs across the top of the windshield, and Mopar logos grace both sides of the car just beneath the side windows. Red decals run back from the rear quarter panels and connect across the rear of the car. It also has hood pins on the SRT Hellcat hood and a parachute attached the rear. There's a parachute because this is the factory turnkey drag-race-focused Dodge Challenger racecar. Mopar released no other information on what type of hardware the Drag Pak will be using, or what's under the hood, but the video gives a great preview of the exhaust note in full tire-smoke mode. As some Drag Paks in the past have dropped roughly 1,000 pounds from their production starter vehicles, the 2020 model will surely utilize plenty of weight-savings methods such as the removal of all interior comfort features that don't apply on the racetrack. Mopar has also previously altered the position of the engine and changed the wheelbase to the benefit of better weight distribution. Mopar is set to livestream the unveiling starting at 7:26 p.m. ET (that's 4:26 on the West Coast, which not coincidentally coincides the the displacement of the vintage 426 Hemi engine) on Nov. 5, 2019. Until then, check out the 2009, 2010, 2011, or 2016 Drag Paks.

Fiat Chrysler will invest up to $1.5 billion to build EVs in Windsor

Fiat Chrysler Automobiles will invest between $1.35 billion and $1.5 billion in its Windsor assembly plant in Canada to build electric vehicles as part of a tentative deal with Canadian autoworkers, Unifor National President Jerry Dias said on Thursday. The auto union said FCA would invest in a state-of-the-art vehicle platform that will enable the assembly of plug-in hybrid and battery electric vehicles, with at least one new model in 2025. The announcement comes less than a month after Unifor said Ford would invest $1.46 billion in its Oakville and Windsor plants. "Not only is Fiat-Chrysler maintaining the current portfolio but they will be investing three derivatives to enhance the current portfolio," Dias said. Unifor also said it expects to extend the life of the Chrysler 300, a rear-wheel-drive luxury car and introduce multiple derivatives of the Dodge Charger and Challenger. The union said as many as 2,000 jobs would be added in 2024 at the Windsor plant. Market forecasting firm LMC Automotive on Thursday said it would take until 2024 for U.S. vehicle sales to recover from the coronavirus downturn and get close to the 17 million vehicles sold in 2019. Ratification meetings for the FCA deal will happen over the weekend, and members will vote on whether to accept the agreement on Sunday. The union is expected to begin negotiations with General Motors's Canadian unit next week. Related Video: Green Hirings/Firings/Layoffs Plants/Manufacturing UAW/Unions Chrysler Dodge Fiat Jeep RAM Coupe Electric Sedan windsor