1969 Dodge Coronet Suoer Bee 440 Hardtop on 2040-cars

Auto blog

Stellantis not looking for further mergers, including with Renault

MILAN — Stellantis Chairman John Elkann on Monday denied the carmaker was hatching merger plans, responding to press speculation about a possible French-led tie-up with rival Renault. Elkann said that the Peugeot owner, the world's third largest carmaker by sales, was focused on the execution of its long-term business plan. "There is no plan under consideration regarding merger operations with other manufacturers," said Elkann, who also heads Exor, the Agnelli family holding company that is the largest single shareholder in Stellantis. After abandoning the Russian market, at the time its second largest after France, and reducing the scope of its global cooperation with Nissan, Renault has been seen as a potential M&A target. Speculation intensified after an electric vehicle market slowdown forced it last week to cancel IPO plans for its EV and software unit Ampere. Its market cap remains stubbornly low at little over 10 billion euros ($10.8 billion) despite a financial recovery over the past few years. Stellantis, the product of a 2021 merger between France's PSA and Fiat Chrysler and one of the most profitable groups in the industry, has a market cap of more than 85 billion euros when unlisted shares are factored in. It has a 14 brand portfolio also including Citroen, Jeep, Opel and Alfa Romeo. NEWSPAPER REPORT Italian daily Il Messaggero had said on Sunday that the French government, which is Renault's largest shareholder and also has a stake in Stellantis, was studying plans for a merger between the two groups. A spokeswoman for Renault said on Monday the group did not comment on rumors. France's Finance Ministry had declined to comment on Sunday. Stellantis has crossed swords with the Italian government, which has accused it of acting against the national interest on occasions. Industry Minister Adolfo Urso last week raised the prospect of the Italian government taking a stake in Stellantis to help to balance the French influence. Renault shares pared gains after Elkann's comments to stand 1.2% higher by 1220 GMT, having initially risen more than 4%. Stellantis CEO Carlos Tavares, a Portuguese-national, last week said in an interview with Bloomberg that the group was "ready for any kind of consolidation" and that its job was to make sure that it would be "one of the winners". Analysts, however, question the rationale of a Stellantis-Renault merger, which would also expand the group's excess capacity in Europe.

Junkyard Gem: 1988 Dodge Aries America LE Station Wagon

During the late 1970s, Chrysler appeared doomed as outdated car designs and a second catastrophic oil crisis caused by Middle Eastern conflict hammered sales. Chrysler had some successful economy cars made by Mitsubishi or based on Simca designs, but the need for an efficient, modern front-wheel-drive platform grew desperate. After a government bailout in 1979 bought some time, CEO Lee Iacocca masterminded the creation of the all-new K Platform, which hit showrooms for the 1981 model year. The first two K-Cars, the Plymouth Reliant and Dodge Aries, were big sales successes, and Chrysler went on building vehicles based on the platform through 1995. Here's an example of the later Aries wagon, found in a Phoenix self-service wrecking yard. The "true" K-Cars were the Aries, the Plymouth Reliant, the Chrysler LeBaron, and the Dodge 400. They have become very rare in wrecking yards today, so I honor their historical significance by documenting the ones I find. During my junkyard expeditions, I have photographed this '81 Aries wagon, this '81 Reliant wagon, this '82 Aries wagon, this '82 400 coupe, this '82 LeBaron convertible, this '83 Aries sedan, this '83 LeBaron Town & Country wagon, this '85 LeBaron woodie convertible, this '86 Aries sedan, this '86 LeBaron Town & Country wagon, this '86 Reliant wagon, and this '89 Reliant coupe. The early K-Cars could be purchased with optional Mitsubishi Astron 2.6-liter four-cylinder (complete with "HEMI 2.6" badging), but in 1988, the choices were down to a 93-horsepower 2.2-liter Chrysler-built four-cylinder or a 2.5-liter version of the same engine rated at 96 horses and 13 extra pound-feet of torque. This car has the 2.2. The "America LE" trim level was the only one available for the 1988 Aries, and it resulted in a fairly Spartan car. Tough, scratchy cloth upholstery and lots of hard plastic were the order of the day. The MSRP on this car started at $7,695, or about $16,770 in 2018 dollars. That's a lot of car for that kind of money. For comparison, the rear-wheel-drive (and much bigger) 1988 Pontiac Safari wagon went for nearly twice that price. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. By 1988, the Aries wagon was looking pretty old, but it was a bargain.

The Dodge Demon's massive drag tires are just barely street legal

Despite the gaffe that was the Vin Dieselgate leak (no, not that one), Dodge and SRT are soldiering on with the twelve-part Dodge Demon rollout in the lead up to the car's reveal at the New York Auto Show. The Vin Diesel video showed what is almost assuredly the car's front, but now we get an official view of the Demon's rear in this week's video, "Wide Body." Along with the new view, Dodge shows off a cryptic license plate (Michigan #2576@35) and details on the Demon's tantalizing wheel and tire combo. That wheel and tire combo, meant to fill out the Demon's new wide wheel arches, is frankly impressive. Lightweight 18- by 11-inch wheels are wrapped in special Demon branded Nitto NT05R tires measuring an astounding 315/40R18 at all four corners. Not only does that trump the old Camaro Z/28's 305 section tires, it makes the Demon the first production car to come equipped from the factory with drag radials, claims Dodge. Presumably, the goal with the Demon is to provide enough power and grip to rotate the Earth underneath the car rather than propelling the car itself down a dragstrip. Beyond that, few other details were revealed. Dodge provided some vague information about how the "wide-body is laser clearanced, and the entire chassis is e-coated for durability before final assembly," but doesn't actually explain what that really means. We do know now that the flared fenders add 3.5 inches to the Demon's overall width. Overall, the car looks mean and purposeful, especially wrapped in just barely street-legal rubber. Follow along at www.ifyouknowyouknow.com and see if you can find and decipher all the hints. Related Video: Design/Style New York Auto Show Dodge Coupe Performance tires dodge demon dodge hellcat