Dodge Challenger 1970 R/t 440 U Code A33 Track Pac Bumble Bee Hemi Orange 4speed on 2040-cars

Auto blog

Dodge Challenger SRT Hellcat #0001 raises $825,000 for charity

$60,000 doesn't strike us as a lot to pay for a muscle car with 707 horsepower on tap. $825,000... now that's a different story. But, according to the official SRT blog, that's how much one generous and eager buyer paid for the privilege of getting his (or her) hands on the very first new Dodge Challenger SRT Hellcat.
Decked out in Stryker Red paint that's usually reserved for the Viper, the supercharged Challenger bearing the VIN 0001 went up for auction at the Mandalay Bay hotel and casino in Las Vegas on Saturday under the auspices of Barrett-Jackson. By the time bidding ended, the gavel dropped at $825,000 - nearly 14 times the sticker price - 100 percent of which will benefit Opportunity Vehicle, a charity that aids the intellectually handicapped in the Las Vegas Area.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2013 Dodge Challenger V6 recalled for fire risk, owners asked not to drive

Chrysler has issued a recall for the V6 version of the 2013 Dodge Challenger (as pictured above in 2012MY) over the possibility of a wiring harness that could short circuit and lead to a fire. Owners of these V6 Challengers built from November 2012 through January 2013 are being urged to contact dealers immediately and, in the meantime, not to drive their cars or park in or near any buildings.
Chrysler estimates around 2,500 potentially affected Challengers are in owners' hands, while another 1,900 are still sitting on dealer lots. The total number of recalled vehicles is 4,459.
So far, Chrysler says that seven fires have been reported - none resulting in injuries. The company is instructing vehicle owners to contact their dealer to find out if their vehicle is included in the recall, but owners can also find the build date information of their vehicle by checking the label in the driver's door jamb.