2009 Heated Leather, Navigation, Xm Radio, Sunroof, Tint, Cd Player, Cruise on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Demon's NHRA competition ban: Good talking point, bad feature

One of the biggest headlines for the Dodge Challenger Demon is that, in stock form, it's so fast that the NHRA won't allow it to compete in the organization's events. It's the ultimate humble brag, "I can't drag race my car because it's so fast it was banned by the sanctioning body." Certainly Tim Kuniskis, head of FCA brands in North America, was excited. He told the press that he hugged the guy that brought him the letter banning the Demon from competition. Unfortunately, the reality is that not being NHRA-legal is kind of silly, and frustrating for owners who would want to actually race. Before we go too much farther, we should explain exactly why the Demon is illegal for NHRA competition. The car is capable of a sub-10-second quarter-mile time both on racing fuel and 91-octane pump gas. Cars that fast are required by the NHRA to have a full, certified roll cage, and the Demon doesn't. Now there are certainly ways to get around this. The most obvious would be for a Demon owner to have a company install a roll cage. Using less grippy tires than the barely street-legal Nitto cheater slicks would probably help bring that time down, too. There's also the option of putting the car into Eco mode, and, yes, the Demon has one. In Eco mode, the Demon makes just 500 horsepower, and trips the lights at the quarter-mile in 11.59 seconds, which will avoid the roll-cage requirement. However, none of these options are ideal. For one thing, if you bought an 840-horsepower car, you're not going to want to limit it when you get to a closed course such as a drag strip. Similarly, you're not going to want to ditch your super-sticky tires at the strip, especially when they're standard equipment. Finally, having to go aftermarket for a roll cage is an inconvenience at minimum, and it seems like a strange oversight considering the rest of the car. This is a car from the factory that comes with drag radials, no passenger seats, a racing fuel tune, air conditioned intercooler, and even skinny front wheels for drag racing. Its purpose is clear, but for some reason, Dodge stopped short of giving it a roll cage that would allow it to compete. Perhaps adding a roll cage would've made it difficult to pass safety regulations, and we would be more disappointed if the car wasn't allowed on the street. Even so, it seems like an odd stopping point.

1968 Dodge D200 'Lowliner' adds low-down diesel torque to a lowrider

When Mopar does a custom classic car, it's always spectacular, whether it's a Dodge muscle car like the 1,000-horsepower Super Charger or the monster Jeep Five-Quarter off-road pickup. For SEMA this year, Mopar skipped another Dodge sports coupe in favor of a 1968 Dodge D200 pickup truck done up as a lowrider, but with a twist. Or more accurately, with lots of twist. Under the gorgeous candy red metallic body is a 5.9-liter 24-valve Cummins turbodiesel straight-six. It makes an estimated 325 horsepower and 610 pound-feet of torque, and it's paired with a six-speed manual transmission. Representatives from Chrysler estimated the weight of the engine and transmission alone at 1,100 pounds. The diesel engine's power goes to the rear wheels, which are 22 inches in diameter and 11 inches wide with fat 325-mm tires. The front wheels are a tad narrower at 9.5 inches. 1968 Dodge D200 View 7 Photos As cool as the powertrain is, the exterior and the interior of the truck can't be ignored. This generation of Dodge pickup is already intriguing with its distinct character line with a little kink at the end and ribbed and louvered hood. These unique styling cues are accented now that Dodge removed various other details from the body such as the door handles, metallic trim and such. The bumpers were also reshaped to better fit the contours of the body, and the front wheels were pushed forward to reduce the long overhang of the stock truck. The bumpers, grille, and "smoothie" style alloy wheels were also painted in a solid cream color rather than chrome, which both accents the deep red body and gives the truck a more workmanlike feel, as low-trim cars typically had painted trim instead of chrome or stainless steel. The red paint also features subtle Cummins logos on the fenders and Dodge block lettering on the tailgate. The interior continues the simple and classy theme. The original bench seat remains, but with saddle brown leather upholstery. Leather trim has been added throughout, and exposed metal parts have been painted in the same color as the exterior. Simple gray cloth floor mats cover the bottom of the cab, and the instrument panel uses new Mopar gauges in a machine-turned metal housing. The original steering wheel remains, but a custom shifter with red Cummins shift knob sticks through the floor.