2004 Chrysler Pacifica Touring Awd Nav Sunroof 3rd Seat Entertainment Leather on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Ford F-150 bumps Camry from top of Cars.com American Made Index

With July 4th just around the corner, what better time could there be for Cars.com to announce that the Ford F-150 is the Most American car of 2013? This may be especially true since it was the Toyota Camry, a car produced by a company based in Japan, that had held the top spot from 2009 to 2012.
Cars.com compiles its Most American list by considering the amount of parts each vehicle uses that come from America, where it's final assembly takes place and how many units per year are sold. "While the assembly point and domestic parts content of the F-150 didn't change from 2012-2013, vehicle sales are responsible for bumping the F-150 to the top spot," according to Patrick Olsen, Editor-in-Chief of Cars.com.
As far as automakers go (as opposed to individual models), Toyota retains the top spot it held in 2012, with General Motors, Chrysler, Ford and Honda (in that order) rounding out the list. The motivation behind this list each year, according to Olsen, is "to help car shoppers understand that 'American-Made' extends beyond just the Detroit three" and because "a study we conducted in 2012 indicated that 25 percent of shoppers surveyed preferred to buy American."

Jeep to stop using bad Takata airbag inflators next week

FCA is gradually ceasing to produce vehicles equipped with Takata airbag inflaters found to be inherently faulty. These airbags, which lack a certain drying agent, have been linked with dangerous premature ruptures. According to FCA, the only vehicle still in production with the named airbag is the 2016 Jeep Wrangler, and in this case they are passenger-side airbags. Fiat Chrysler says it isn't aware of any incidents involving these air bag inflaters in Jeeps, but amidst concerns that vehicles with failure-prone airbags are still being marketed to customers, North American-market 2016 Wranglers will cease to be equipped with them starting next week. As per FCA's statement, global production is expected to end by mid-September. In addition to Toledo, Ohio, the Wrangler is produced in Egypt. FCA isn't going to sell the cars with the deemed-faulty airbags without disclosing the fact to the customers: anyone buying a 2016 Wrangler will be notified that the vehicle will most likely be subject to a recall in the future, even if there is not currently a recall announced for them. NHTSA has specified a "Coordinated Remedy Program" recall schedule for the coming years, and the airbag inflaters will degrade over a time frame of several years, when subjected to a humid environment. Related Video: News Source: Fiat Chrysler Automobiles, The Wall Street JournalImage Credit: Julien Amado / Autoblog Quebec Plants/Manufacturing Recalls Chrysler Jeep Ownership Safety Takata airbag recall