2012 Chevrolet Suburban Lt 4x4 Loaded, Only 32,000 Miles, Local Trade on 2040-cars

Auto blog

GM ending stop-sale order on heavy-duty trucks

General Motors responded to an inquiry from Autoblog regarding a stop-sale order on its full-size heavy-duty pickup trucks. Here's GM's official statement. GM is committed to building the highest quality products possible. We paused delivery on a small number of HD pickups with the 6.6 liter Duramax engine last week to finalize an investigation into a potential quality issue. The investigation has been completed and the stop sale will be lifted for the small number of vehicles at dealerships.Customers can be assured GM’s heavy duty pickups are covered by a 5 year/100,000 mile powertrain warranty. The original article continues below. General Motors has reportedly sent its Chevrolet and GMC dealers a stop-sale order that applies to some examples of the 2022 Silverado HD, the 2022 Silverado MD, and the 2022 Sierra HD. The units affected by the stop-sale order may develop an engine-related problem. Citing anonymous sources, website GM Authority wrote that the Duramax 6.6-liter turbodiesel V8 in the affected trucks can hydrolock, which means liquid could enter the cylinders and cause a substantial amount of damage. The report does not specify where the liquid would come from; hydrolocking can happen by driving through a deep puddle of water, for example, but a large amount of coolant can cause it as well. The publication adds that the stop-sale order was assigned internal reference number N222362910. It also notes that the trucks included in it can't be sold, delivered to buyers, traded with another dealer, sent to auction, or even used for demonstration purposes until further notice. Earlier in April 2022, GM Authority reported that General Motors planned to buy back an unspecified number of Silverado HD and Sierra HD trucks due to quality-related issues with the 6.6-liter V8. Details about the problems experienced by customers haven't been released; all we know is that each truck will be replaced, though the replacement may not have the same equipment due to the ongoing chip shortage. Related video:

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

Chevy Bolt will go into production in Michigan in 2016 [UPDATE]

While nothing official has been announced, it appears that General Motors may actually put the all-electric Chevy Bolt into production next year. That's the rumor that Reuters is reporting, citing two sources at suppliers for the upcoming $30,000 EV (although that $30,000 number bears some scrutiny). This rumor does fit in with earlier comments that the Bolt would arrive on the market in 2017. If it gets built, the Bolt will share more than a similar-sounding name with the Chevy Volt: the EV will be put together in metro Detroit. Reuters says the 200-mile electric car (and an Opel version) will be made in "an underused small-car plant north of Detroit," which means the Orion Township plant. GM could make between 25,000 and 30,000 Bolts a year there, if what the suppliers are saying is true. We have asked GM for a statement on this story and will update it if we hear back. UPDATE: General Motors manager of electrification technology communications, Kevin Kelly, told AutoblogGreen that, "Bolt EV Concept is just that – a concept. We're currently evaluating the vehicle program, but do not have any production announcements to make at this time."