2014 Chevrolet Silverado 1500 Ltz on 2040-cars

Auto blog

Genovation Cars readies all-electric Corvette prototype

Chevy runs the full spectrum from some of the most environmentally friendly cars to the least. At one end are EVs like the Spark and Volt. At the other, performance models like the Camaro and Corvette. But one American company wants to bridge that divide. That company is Rockville, MD-based Genovation Cars, which reports that it is almost done building its prototype for an all-electric Corvette. Dubbed the Genovation Extreme Electric (or GXE for short), the prototype is based on a previous-generation 2006 Chevy Corvette Z06, but ditches its enormous 7.0-liter V8 for an array of inverters, batteries, and electric motors said to be good for over 700 horsepower and 600 pound-feet of torque. That promises to deliver a 0-60 time of about 3.0 seconds and a top speed in excess of 200 miles per hour. Those are supercar benchmarks for performance if we've ever seen them, and ought to leave even the top-spec Tesla Model S P85D in... well, not a cloud of smoke, but whatever the electric equivalent is, in a non-polluting cloud of that. The GXE is also supposed to be able to travel for 150 miles on a single charge, and handle well while it's at it with 50/50 front-rear weight distribution and a low center of gravity. Sorta like the Power Wheels 'Vette pictured above, then, but bigger and faster. Look for the GXE to debut at the Electric Vehicle Technology Expo this coming September in Michigan, after which Genovation says it will put the GXE to the test on the track to back up its performance claims. Genovation Cars Nearing Completion of High-Performance All-Electric Corvette, the GXE ROCKVILLE, Md.--(BUSINESS WIRE)--Genovation Cars is nearing the completion of a prototype high-performance all-electric Corvette called the Genovation Extreme Electric or GXE. Assembly of the GXE will be completed by the end of July, followed by a three-week testing phase. The GXE is based on a 2006 Z06 Corvette. Several contributors to the GXE effort have helped design and build record-breaking electric vehicles. They include an MIT electrical engineer and a mechanical engineer from Cosworth. "We are using state of the art inverters, batteries and electric motors that will produce in excess of 700-hp and 600 lb-ft of torque," said Genovation CEO Andrew Saul. "We expect the car to achieve 0-60 mph in around three seconds and have a top speed of over 200 mph.

GM says hybrid Corvette no laughing matter [w/poll]

When Mark Reuss was in LA recently, he sat down to have a few words with the scribes at the Los Angeles Times. When the issue of a hybrid Corvette came up, Reuss answered with "Don't laugh." The General Motors president is a complete fan of the possibility, calling it "attractive" and "really fun," believing it would improve GM expertise and that "people would love it."
Naturally, the president being supportive of an idea doesn't give indication that a hybrid Corvette is on the way. However, with supercars like the Porsche 918 Spyder and Ferrari LaFerrari giving hybrid tech a solid, if remote, place in the performance car world, the inexorable trickle-down of technology means we shouldn't be surprised if and when it does happen.
And now that we have that non-negative half-answer to a speculative question, it would be irresponsible for us not to commence rumormilling for the C8 Corvette. Taking Reuss at his word, the C8 will obviously be a hybrid with all-wheel-drive - the left side wheels driven with electric motors, the right side with the mid-mounted, four-cylinder diesel engine. With coefficient of drag of just .16, figure on a 0-to-60 mile-per-hour time of under 2 seconds and an all-electric range of something like 30 miles at top speed. Don't forget, folks, you read it here first.

Why an independent rear suspension for GM's new, full-sized SUVs wasn't easy

A Motor Trend report last month laid out how Cadillac's 4.2-lier twin-turbo Blackwing V8 could be an orphan due to cost concerns in the GM empire. Last-minute chassis changes to Cadillac's new sedans and XT6 crossover led to engine bays that couldn't fit the Blackwing. On the SUV side, according to the report, the new independent rear suspension for big people haulers cost so much to implement that GM ruled out reworking the Escalade to accept the Blackwing. At least one commenter rightly asked how could a suspension swallow that much money. A new piece in Motor Trend has the answer. The excellent Alissa Priddle spoke to Tim Herrick, GM's executive chief engineer for full-size trucks, about why the clean-sheet IRS cost "multimillions of dollars."  First, GM would need to build a new body shop at the Arlington, Texas plant that assembles the automaker's big SUVs to stamp the numerous wholly new parts and panels accommodating an IRS. Then GM would need to design and pay for a new assembly process. On top of those up-front costs, there was the incremental cost of the four-link IRS components being more expensive than those in the trucks' former leaf-sprung solid axles. Herrick endured so many rejections for so long that he remembers the date and time when he got approval for the new unit. He said it came down to a meeting where he told a higher-up, "I'll make you a deal: If we get to the reveal, or if we launch this and you think this was a dumb idea, I'll hand you my badge and let you walk me out." Head to Motor Trend to read the full story. Based on Herrick being on stage to help present the new SUVs to the press, and on our First Ride in the new Chevrolet Tahoe and Suburban at GM's Milford Proving Grounds, it appears this will have a happy ending for all involved. Furthermore, since Herrick worked on the T1 platform that supports the big SUVs as well as the light- and heavy-duty pickups, he understood the demands on the commercial side, too. That could be why when Roadshow asked Tim Asoklis, chief engineer of the Tahoe and Suburban, if the new IRS could endure life in the Chevrolet Silverado and GMC Sierra, Asoklis answered, "Oh, absolutely." Related Video: