2000 Chevy 1 Ton 3500hd - Non Running - Needs Tlc on 2040-cars

Auto blog

There are still 6,000 first-gen Chevy Volts on dealer lots

The next-gen 2016 Chevrolet Volt looks to be a pretty fantastic vehicle with more electric driving range, better fuel economy than its predecessor, and a lower starting price. However, if you're looking for a deal, the 2015 model of the plug-in hybrid might not be a bad place to check because Chevy has a ton of them to get rid of. According to The Detroit Free Press, there are around 6,000 examples of the 2015 Volts that are still sitting on dealer lots. That might not sound like a lot, but Chevy only sold 905 of them in April and 2,779 through that month in 2015. It moved 18,805 of the PHEVs for all of 2014. Buyers are in a pretty good spot to haggle at the moment, too, with the a new Volt right around the corner. According to The Detroit Free Press based on TrueCar figures, the current average closing price for a 2015 model is $30,607 before any federal or state tax credits. You can also lease one for 39 months for $299 a month and $1,649 due at signing. In April, Chevy was reportedly offering customers 2.9-percent financing for 48 months and leases with no money down for buyers trading in a vehicle from a competitor. Of course, there's also always the option to buy a pre-owned example. Just a few months ago, prices for used Volts were reportedly as low as $13,000 at auction.

2020 Chevy Silverado, GMC Sierra recalled due to faulty brake component

General Motors is recalling 2020 Chevrolet Silverado 1500 and GMC Sierra 1500 pickups to fix a defect in the trucks' brake system. Certain Silverado and Sierra pickups were produced with brake-caliper bolts that were not heat-treated. Without heat-treating, the bolts are weaker than they should be, and there is a risk that they could fail, which would affect the trucks' braking performance, possibly leading to a crash. In total, 20,352 vehicles are affected. Owners of affected trucks will be contacted by GM. Dealers will inspect the bolts and replace those that are defective. Related Video:      

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.