Pro-street Chevy Ii Nova Real Ss on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Camaro driver clocked at 171 miles per hour

Chevy's 2016 Camaro SS is a fantastic piece of automotive engineering. It is also, apparently, very, very fast. This latter fact was perfectly illustrated when, on April 8, a Camaro SS driver was nailed in Two Harbors, Minnesota for doing 171 mph. According to WFAA, the unnamed speed demon was flying down Highway 61 near Two Harbors when Hermantown, MN Deputy Police Chief Shawn Padden clocked him at an eye-watering 171 mph. He then recorded the speeder at 168 and 141. At the time, Deputy Chief Padden was working with Minnesota State Patrol on an anti-DWI program called "Toward Zero Deaths". Padden, who was interviewed by the Duluth News Tribune, said he was surprised at the driver's sheer speed. "When he went by me, it was a blur," Padden told the News. "You get used to seeing people going 65 or 70 and what that looks like. But I've never seen anything like this. It's like a rocket on wheels." Fadden chased the Camaro down eventually, but it took some doing. To catch the Camaro, he pushed his Dodge Charger Pursuit to 135 mph just to get into range so the Camaro could see his emergency lights. The speeding driver was ticketed for careless driving, but may lose his license due to a Minnesota law that gives courts the option of revoking licenses for drivers caught doing more than 100 mph. News Source: WFAA, Duluth News Tribune Weird Car News Chevrolet Dodge Driving Safety Coupe Police/Emergency Performance Sedan camaro ss camaro

GM to squeeze out more production capacity for midsize trucks

General Motors was predicting a strong showing for the Chevrolet Colorado and GMC Canyon before they debuted, and demand among dealers for the midsize trucks even exceeded company's expectations. The positive situation has left GM with a problem, though: finding ways to increase capacity for the pickups at the Wentzville Assembly plant in Missiouri. With a third shift already running, GM has continued to look for ways to build just a few more of the trucks at the plant. The company has plans to hire as many as 1,000 more workers for the Saturday and Sunday shifts to construct an additional 2,000 pickups a month, according to unnamed insiders at the factory speaking to Automotive News. The little adjustments even extend to getting rid of an unpaid break to add 18 minute of assembly time over the course of a day, which equals about 3,500 more vehicles a year. All of this effort comes because the trucks are in such high demand. According to GM's figures, the company has delivered a combined 35,720 units of the Colorado and Canyon from January through April 2015, and the Chevy was the fastest-selling truck in the US for the previous three months. In May, it spent an average of just 12 days in showrooms before being snapped up. And even better for the company, 43 percent of these buyers came from other brands. According to Automotive News, the most popular trade-ins have included the Ford F-150, Toyota Tacoma, and Dodge Dakota. Related Video: