2011 Chevrolet Camaro on 2040-cars

Auto blog

How GM engineers are using diaper 'snow' to keep you warm

Testing how snow affects General Motors' vehicles isn't really a problem right now for the company's engineers, but in the dog days of summer the process isn't exactly easy. The only real option is for them to book time at the automaker's climatic wind tunnel. However, a flash of brilliance from an engineer allows snow to be simulated regardless of the temperature outside, and the discovery is all because of his daughter's wet diaper. The realization came to GM Thermal Systems engineer Nicholas Jahn while he was swimming with his daughter and noticed how her diaper ballooned in size in the water. He found out the substance that makes this possible is called sodium polyacrylate. When the material gets wet it grows and forms fluffy flakes that are a close imitation of snow. Best of all, the stuff can be prepared easily any time of the year, and it's reusable. The engineering team uses the material to test the effectiveness of the heating systems of GM's vehicles. They spread the sodium polyacrylate over the inlets at the base of the windshield to obstruct the airflow and then crank the heater. After some time, they can see how much is being sucked into the system and design more efficient systems in the future. See how the process works in the video above and read about the diaper discovery in GM's press release below. Diapers Change Chevy Cruze Winter Warm-up Time GM validation engineer uses diaper material "snow" to reduce frigid drives 2015-01-06 DETROIT – An item commonly found on an infant's changing table is helping General Motors' engineers simulate snow year round, ensuring heating systems in cars like the 2015 Chevrolet Cruze can quickly and efficiently warm its interior. Packed snow can prevent air from entering the inlet panel at the bottom of the windshield, obstructing the flow of air into the heating system and reducing the amount of air it can push out. This can lead to less efficient warming of the car's interior and windshield defrosting. "The last thing anyone wants to do when it's freezing cold out is scrape their windshield," said Nicholas Jahn, GM Vehicle Thermal Systems engineer. "The testing we perform on the Chevrolet Cruze with the diaper material allows us to maximize the car's heating capabilities." Ironically, Jahn stumbled upon his diaper-based testing method in the middle of summer. During a swim with his daughter, he noticed her diaper multiplied in size when it came into contact with water.

GM Ultium tech can scavenge heat from everywhere, even you

GM likes to give us tidbits about its Ultium platform from time to time, and today it’s telling us about the platformÂ’s ability to capture waste heat from the propulsion system. In addition to capturing from the propulsion system, it can also capture humidity from both inside and outside the vehicle and even from passengersÂ’ body heat. Yes, you, your family and/or your friends are a usable heat source as far as GM EVs are concerned. It then deploys the heat in an advantageous way. If at this point, youÂ’re screaming, "Heat pump!" youÂ’d be right. WeÂ’re talking about an elaborate heat pump system that GM is using for its Ultium-based vehicles. Every Ultium-based GM vehicle gets this system that is covered by 11 patents and four publications. The waste heat it collects is used in a number of ways, but its primary use is to heat the cabin quickly and efficiently. GM claims it can heat the cabin of its Ultium-based vehicles quicker than vehicles with traditional internal combustion engines. Plus, when put to use, GM claims that using the heat pump provides its EVs with up to 10% more range than theyÂ’d have without. Beyond heating the cabin, the heat pump is capable of putting waste heat to use by preheating the battery prior to charging so that you can charge quicker. The system can even cool the propulsion system in preparation for Watts to Freedom (WTF) launch control starts. GM says this was vital in helping the Hummer EV achieve its bonkers 0-60 mph time of about 3 seconds. “Having a ground-up EV architecture gives us the freedom to build in standard features like UltiumÂ’s energy recovery capabilities,” said Doug Parks, GM executive VP of global product development, purchasing and supply chain. “This helps us squeeze more efficiency, performance and overall customer benefit out of our EVs.” GM says itÂ’s been developing heat pump technology since the EV1 and its heat pump. This is the modern evolution of that technology, and GM says itÂ’s going to be implemented in every Ultium-based vehicle as a standard feature. Related video: Green Cadillac Chevrolet GM GMC Technology Electric Future Vehicles

Watch this creative way to pull a truck's engine

Living in an apartment complex has its benefits, but for shade-tree mechanics who like/need to work on their own cars, it definitely has a number of disadvantages. Relatively simple tasks such as brake jobs and oil changes are difficult when you don't have dedicated driveway space, to say nothing of more in-depth repairs... like pulling an engine, for example.
For these types of challenges, a little ingenuity and plenty of muscle are needed to get the job done. Scroll down to watch these four men snatch the V8 out of a Chevrolet K1500 using nothing but a chain, landscape timber and good ol' fashioned brute strength. Good work, gentlemen.