1984 Chevy Military Pu Diesel 1 Ton 4x4 Dana 60 Front End Low Mileage on 2040-cars

Auto blog

2014 Chevrolet Malibu gets more torque, more room and inspiration from the Impala

The 2014 Chevrolet Malibu, having stared at the Impala across the showroom floor for a year, gets nips and tucks all over inspired by its larger brother. The 2.5-liter four-cylinder in the base car will get a stop-start system and 23 city miles per gallon, 35 highway, each number representing a one-mpg improvement over the 2013 car. Output is 196 horsepower and 186 pound-feet of torque.
Opt for the 2.0-liter turbo and, while power holds steady at 259 hp, torque goes up by 14 percent to a striking 295 lb-ft (a figure Chevy calls best in the class). The final details include newly programmed transmission shift points and faster shifts, for better engaging and enjoying the added power.
Looks-wise, the grille's been reshaped to be more in line with the new Chevrolet look, a narrower upper grille hovering over a larger lower grille.

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Surprise! GM putting aluminum in next-gen pickups

Last month, General Motors launched a series of ads touting the benefits of steel over aluminum – specifically, with regard to the Chevy Silverado versus the Ford F-150. (Kind of. We're not sure what a grizzly bear has to do with anything.) We took issue with the ads, with editor in chief Mike Austin saying they "reek of insecurity, and distract from the Silverado's strengths that could be used for positive advertising." But what bothers us more, is that yet another report surfaced claiming anti-aluminum GM will indeed use the weight-saving material in its next-generation fullsize trucks. On Tuesday, GM announced a $877-million investment for its truck plant in Flint, MI. But Reuters says that huge overhaul is because the trucks will use "substantially different equipment than the tools GM uses today." The report specifically states, "People familiar with the company's plans say GM's next-generation pickups and SUVs will make use of various materials, including aluminum and lightweight steel, to shed weight and gain fuel efficiency to meet tougher federal standards." The Silverado already uses a few aluminum components in the engine and hood, and if more widespread use will help GM build its best fullsize trucks ever, then that's great. Honestly, we have no reason to doubt that aluminum will be used in the next Silverado and GMC Sierra. We just hope GM remembers that nothing is ever truly deleted from the bowels of the Internet when it launches the subsequent "look how great aluminum is!" campaign. Related Video: News Source: Reuters Green Plants/Manufacturing Chevrolet GM GMC Truck aluminum steel