1995 Chevrolet C1500 Base Extended Cab Pickup 2-door 5.7l, No Reserve on 2040-cars

Auto blog

GM to cut production at 5 plants in North America, kill several models

DETROIT/WASHINGTON — General Motors Co said on Monday it will cut production of slow-selling models and slash its North American workforce in the face of a stagnant market for traditional gas-powered sedans, shifting more investment to electric and autonomous vehicles. The announcement is the biggest restructuring in North America for the U.S. No. 1 carmaker since its bankruptcy a decade ago. GM said it will take pre-tax charges of $3 billion to $3.8 billion to pay for the cutbacks, but expects the actions to improve annual free cash flow by $6 billion by the end of 2020. GM plans to halt production next year at three assembly plants: Lordstown, Ohio, Hamtramck, Michigan, and Oshawa, Ontario. The company also plans to stop building several models now assembled at those plants, including the Chevrolet Cruze, the Cadillac CT6 and the Buick LaCrosse, the sources said. Sources said the Chevrolet Volt, Impala and Cadillac XTS would also be discontinued. Signs of the demise of six passenger-car models have been swirling since July. Plants in Baltimore, Maryland, and Warren, Michigan, that assemble powertrain components have no products assigned to them after 2019 and thus are at risk of closure, the company said. It will also close two factories outside North America, but did not identify those plants. The AP reported that 14,700 jobs would be affected. Some 8,100 of those would be white-collar jobs reduced through buyouts or layoffs. The No. 1 U.S. automaker signaled the latest belt-tightening in late October when it offered buyouts to 50,000 salaried employees in North America. The company also said it will cut executive ranks by 25 per cent to "streamline decision making." Some 6,000 factory workers could lose their jobs or be transferred to other plants. Its shares were last up 6.2 percent at $38.16. Tariff 'headwinds' and cost-cutting GM Chief Executive Officer Mary Barra told reporters on Monday the company can reduce annual capital spending by $1.5 billion and increase investment in electric and autonomous vehicles and connected vehicle technology because it has largely completed investing in new generations of trucks and sport utility vehicles. Some 75 percent of its global sales will come from just five vehicle architectures by early in the 2020s. It plans to reduce annual capital spending to $7 billion by 2020 from an average of $8.5 billion a year during the 2017-2019 period.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM natural gas-powered vans recalled due to possible leak

General Motors is recalling almost 3,200 of its compressed-natural-gas powered utility vans because of possible leaks. GM and the National Highway Traffic Safety Administration (NHTSA) released a notice last week saying that 3,196 Chevrolet Express and GMC Savana CNG vans are on recall, though no accidents have been reported due to the possible issue. The recall is specifically for vans for model years ranging from 2011 to 2014. The recall stems from a potential leak from the compressed natural gas high-pressure regulator, and such a leak could cause a fire or explosion. GM will replace the vehicles' high-pressure regulator in order to fix the problem, will do it free of charge and is instructing owners to contact Chevrolet or GMC customer service to arrange for the parts replacement. Utility vehicle makers like General Motors have pushed for fleet sales of CNG-powered vans and trucks for the past few years and have touted them for their cheaper refueling costs relative to standard gasoline, not to mention the fact that natural gas can be readily sourced from throughout North America (thanks, fracking). According to CNGPrices.com, compressed natural gas sells for about $2.22 a gallon, on average, while the AAA is pegging the average price of gas at $3.34 a gallon. NHTSA has posted information on the recall here. Featured Gallery News Source: NHTSA via Reuters Green Chevrolet GM GMC Natural Gas Vehicles CNG gmc savana