1953 Chevrolet Bel Air 2-door Hardtop on 2040-cars

Auto blog

Motor Trend puts Chevy Camaro Z28 and Porsche 911 GT3 Head 2 Head

Motor Trend admits, "This is an unfair comparison." But that doesn't make it any less fun to watch when they pit a Camaro Z/28 against the Porsche 911 GT3. The former has a 7.0-liter V8 with 505 horsepower and 481 pound-feet of torque shifted through a six-speed manual. The latter has a 3.8-liter flat-six with 475 hp and 324 lb-ft shifted through a seven-speed dual-clutch transmission. Yet those are only the little disparities – the big disparities are mass and money: the Camaro weighs 3,882 pounds and costs $76,150 as-tested, the Porsche weighs 3,267 pounds and costs $145,785. But they're both about hardcore performance, so MT takes them out on the street, to the drag strip, to the parking lot for figure eights and a skidpad test, and finally to Big Willow for Randy Pobst to give his professional assessment. Remember when a lotta people spent a lotta time debating Pirates vs. Ninjas? This is like that, only it's the "haul-ass good-time car" vs. the "track surgeon." Enjoy the debate in the video.

Watch a 2015 Corvette Z06 run the quarter in 11.7 seconds

We're not writing about this because it's an amazing run, we're writing about it because it appears to be the first run. Someone took a 2015 Corvette Z06 to Royal Purple Raceway in Baytown, Texas and blasted it down through the quarter mile. It's still wearing the dealer number in wax pen on the windshield and dealer plates, so this example is fresh from the mold. It's also a seven-speed manual. General Motors said the row-your-own Z06 can do the 'strip in 11.2 seconds, and they undoubtedly had a professional driver and more than one run to set that time. To have Just Some Guy show up at the raceway and do an 11.7 at 120.54 mph on his first run means we expect good things to come as Z06s get delivered to their owners. Check out the run in the video.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging