4.2 Avant Manual 4.2l Cd Awd Traction Control Stability Control Brake Assist Abs on 2040-cars

Auto blog

Audi creates new diesel fuel from carbon dioxide and water

What if you could power cars of the future with pollution created by the cars of the past? That's what German automaker Audi is hoping to achieve by creating a new synthetic fuel using renewable energy to turn water and carbon dioxide gas into a new kind of fuel they call "e-diesel." The new diesel is being produced at Audi's pilot plant Sunfire in Dresden, Germany. Only a few gallons were created, which the German Federal Minister of Education and Research Johanna Wanka put into her Audi A8 to prove the fuel's bonafides. The base fuel is known as "blue crude" and begins from a green source. Audi uses electricity from wind, water or solar power sources to separate hydrogen from oxygen in water. The hydrogen is then mixed with carbon dioxide which has been converted in carbon oxide. The blue crude is then further refined to create the e-diesel. The carbon dioxide is currently supplied by a biogas facilities, but some of that CO2 was captured from the air. "The engine runs quieter and fewer pollutants are being created," says Sunfire CTO Christian von Olshausen. The fuel can be combined with conventional diesel fuel, as biodiesel fuels already and would be competitively priced against regular diesel, according to Gizmag. Sunfire can produce about 42 gallons of e-diesel a day. That seems like barely a drop in the bucket in terms of Europe's energy use, but Audi is ready to commercialize the technology with plans to expand production with a bigger facility in the future.

VW stock plummets as Euro markets open

The fallout from Volkswagen's installation of an emissions "defeat device" on nearly 500,000 diesel-fueled models in the US is already hitting the automaker hard on the German stock exchange. At one point, the share price plummeted 23 percent to erase the equivalent of $17.6 billion in value. Things eventually bounced back slightly to a still severe 19.23 percent loss, according to Bloomberg as of this writing. The scandal couldn't come at a worse time for chairman Martin Winterkorn. The VW supervisory board takes up the issue of renewing his contract on September 25, Bloomberg reports. If things get bad enough, the door could be open for a new boss to step in. Dealers in the US might start feeling the pain from this, as well. Affected 2015 VWs that are still at showrooms are now under a stop sale. Until the issue is straightened out, the Environmental Protection Agency isn't certifying the company's 2016 diesel models with the 2.0 TDI, either. The diesel emissions problem was first discovered by research from West Virginia University and the International Council on Clean Transportation. In some cases, the engines can produce 40 times more nitrogen oxides than allowed. The automaker could be on the hook for $18 billion in fines for the breach, but the actual figure is expected to be lower. In response, Winterkorn has issued a public apology and ordered an independent investigation into what happened. The EPA and California Air Resources Board have also been looking into the situation. This could become an international problem, though. According to The Detroit News, European authorities might begin similar inquires to check the automaker's diesel emissions there.

Audi 3D-printed this tiny Type C racer, we want to drive it

See this little guy? No, not the one driving – that's Professor Hubert Waltl, Audi's head of production and Volkswagen's chief toolmaker. The thing he's driving, though, is a 1:2 scale replica of the 1936 Auto Union Type C. And it was 3D-printed entirely in house. Not in one piece, mind you. It's too big for that. But the Audi Toolmaking division employed metal printing technology to fabricate all the parts that went into this replica of one of the most dominant of the Silver Arrow grand prix racers of the pre-war era. It's essentially like the pedal car Audi rolled out nine years ago, or the E-Tron concept it showed us nearly five years ago. Only this one uses more advanced manufacturing techniques. Aside from making us want to drive it like nobody's business, the half-sized vehicle serves to showcase the advancements which Audi and the VW Group are making in manufacturing – particularly in the area of 3D printing. The German automaker presently has the technology to print laser-melted layers of metallic powder – either steel or aluminum – with grains measuring half the diameter of a human hair. The equipment can handle objects as large as 7.9 inches high by 9.5 inches wide – which, as small as this little car looks, is still a bit too large to simply print out in one piece. Audi Toolmaking prints "Auto Union Typ C" - Exact model of the "Silver Arrow" from a 3D printer - Audi Board of Management Member for Production Prof. Dr. Hubert Waltl: "This underscores our pioneering role in toolmaking." From powder to a component: With a 3D printer, Audi Toolmaking has produced a model of the historical Grand Prix sports car "Auto Union Typ C" from the year 1936. The company is now examining further possible applications of metal printers for the production of complex components. At the same time, Audi is creating important synergies with toolmaking in other parts of the Volkswagen Group. "We are pushing forward with new manufacturing technologies at Audi Toolmaking and at the Volkswagen Group," stated Prof. Dr. Hubert Waltl, Audi's Board of Management Member for Production and Head of Toolmaking at the Volkswagen Group. "Together with partners in the area of research, we are constantly exploring the boundaries of new processes. One of our goals is to apply metal printers in series production." The Volkswagen Group has a total of 14 toolmaking units in nine countries. Under the leadership of Prof. Dr.