1968 Ford Torino on 2040-cars
Angier, North Carolina, United States
Engine:390 2v
Vehicle Title:Clear
Fuel Type:Gasoline
For Sale By:owner
Interior Color: Black
Make: Ford
Number of Cylinders: 8
Model: Torino
Trim: base
Warranty: Vehicle does NOT have an existing warranty
Drive Type: auto
Mileage: 12,000
Sub Model: base
Number of Doors: 2
Exterior Color: Yellow
this is a verry sweet car hate to see her go minimal rust runs drives great new bat duel exaust verry rare car gt rims 390 big block new rear bumper hood is damaged mabe fix new fiberglass one is 350.00 this is a headturner thanks
On Mar-18-13 at 15:52:45 PDT, seller added the following information:
the floorpans are vgc as are the framerails no rust tires are good i drive this car every weekend would not take much to restore thanks interior is in pretty good condition
Ford Torino for Sale
- 1970 ford torino sport barn find! great project car!
- 1969 torino fastback, fairlane 500, v8 car, **** great builder ****(US $2,600.00)
- 1971 ford torino gt,grabber yellow,351,4 spd,shaker hood,marti report, original!
- 1970 ford torino 351 barn find classic car automatic top manual trans
- 1971 ford torino convertible
- 1969 torino cobra fastback q code(US $20,000.00)
Auto Services in North Carolina
Wright`s Transmission ★★★★★
Wilburn Auto Body Shop Belmont ★★★★★
Whitaker`s Auto Repair ★★★★★
Trull`s Body & Paint Shop ★★★★★
Tint Wizard ★★★★★
Texaco Xpress Lube ★★★★★
Auto blog
Toyota fears supplier pressure in Australia with GM pull out
Wed, 11 Dec 2013With Ford and General Motors both announcing an end to production in Australia, the country's auto industry is in a bad way. With the exit of two big players, there's increased concern that a third Australian manufacturer, Toyota, will be forced out, as well.
"We are saddened to learn of GM Holden's decision. This will place unprecedented pressure on the local supplier network and our ability to build cars in Australia," Toyota Australia said in a statement. The GM closure of Holden production will be the direct end to 2,900 jobs, but will also force a dramatic reduction in the size of the country's supplier network, as there will simply be fewer cars to build.
In the same statement, Toyota Australia said it would work with suppliers and local government to figure out whether continuing production Down Under was even feasible. According to Automotive News, a representative for the Australian Manufacturing Workers' Union told reporters it was "highly likely" that Toyota would also close up shop within the next few years.
Ford F-Series Super Duty prototype reduced to smoldering mess of aluminum and steel [UPDATE]
Mon, 04 Aug 2014The most important bit of information you need to know after looking through our high-res gallery of images depicting a prototype 2016 Ford F-Series Super Duty pickup truck burning to the ground is that nobody was hurt. There were two engineers inside the vehicle when it caught fire, and both exited to safety.
That's the good news. The bad news is that the truck, which appears to have been testing in Death Valley, appears to be a total loss, minus, of course, whatever information Ford can glean from the conflagration - particularly tracing it back to its root cause. Besides that, we're also expecting the body of the next Super Duty to be hewn from aluminum, as is the case with its smaller brother, the brand-new F-150. Note the little aluminum droppings littering the roadway as apparent proof of that.
Our spy photographers report that it took just 21 minutes for the F-Series Super Duty to burn completely to the ground. The fire appears to have started in the driver-side front wheel well, spreading to engulf the entire front end in three minutes. We can't confirm the source of the blaze, but we're curious if the car's black vinyl cladding, meant to obscure the secrets within, contributed to the fire.
Ford reveals new rapid prototyping and low-volume production techniques [w/video]
Mon, 08 Jul 2013It's called "F3T," and that stands for Ford Free-form Fabrication Technology. The process that The Blue Oval has developed means being able to sidestep the weeks-long process of tool-and-die making when engineers want to construct a new part, allowing them to fabricate a three-dimensional part from a two-dimensional sheet of metal in just hours.
While F3T is being developed it is limited to "low-volume prototyping or even low-volume niche vehicles," but the next step is to evaluate it for use in Ford's global manufacturing facilities. You can find out more about it in the video and the press release below.