~2001 Dodge Durango For Sale~3rd Row Seat~low Miles~4x4~ready To Go~runs Great!~ on 2040-cars

Auto blog

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Help us decipher the cryptic license plate on the latest Dodge Demon teaser

If you've been following along, you know that the slow rollout of the Dodge Demon has been filled with hints and teasers of what's to come. Every release encourages fans to watch the videos over and over to try and catch any hidden info. Last week, brief a glimpse of the wheels in a video hinted at this week's reveal, 18x11 inch lightweight wheels wrapped in what the DOT barely considers street-legal rubber. Along with details on the custom Nitto tires, Dodge released an image of the Demon in all its wide-body glory. Planted on the back of the car is a cryptic Michigan license plate that reads #2567@35. It's obvious that this is another clue, but after a few hours of note taking, Google searches, and general discussion, we can't figure out what it means. We're throwing this out there in the hope that someone has better luck than we did. Here are some of the things we've ruled out: Address or coordinates 1/4 mile ET 1/4 mile trap speed Power Supercharger boost pressure Some event in 1982 A hint at gear or final drive ratio If you have some idea, post it in the comments. Related Video:

Dodge Viper plant will close for good Aug. 31

It has been a long time coming, an end rumored since at least 2015, but after 25 years, the Dodge Viper's demise is nigh. Production of the $90,000 bespoke sports car is ending. Therefore, FCA will be shutting down its Conner Assembly Plant on Aug. 31. Automotive News reports that the Detroit plant will be shutting down. The car has been hand-built there since 1995, save for a hiatus in 2010-13 (production began at FCA's Mack Plant in 1992). The Prowler was built there, too, from 1997 to 2002. More than 80 workers currently build the Viper, making Conner FCA's smallest assembly facility. But not many Vipers are sold - 630 last year - despite an enthusiastic following. And of course FCA's own 707-horsepower Dodge Challenger and Charger SRT Hellcats and new 840-horsepower Challenger SRT Demon can't help matters. But the last straw is the fact the Viper can't comply with new safety requirements going into effect. On the bright side, the UAW has seen the plant closure coming since 2015, and FCA has told the state of Michigan that it expects to find positions at other plants for the Viper crew. FCA has been celebrating the Viper valedictory for a couple of years now, offering serialized special editions, including the $121,000 Viper ACR, and touting the ability to build unique Vipers with its "1 of 1" customization program, with a choice of 16,000 unique paint colors and 48,000 unique stripe combinations. Related Video: