2012 Toyota Prius Plug-in Hybrid Advanced on 2040-cars

Auto blog

Toyota recalling 1.67 million vehicles worldwide in 3 campaigns

Toyota is issuing three separate recalls covering 1.67 million vehicles worldwide with most of those models in Japan. It looks like the campaigns' impact on the US may be smaller, though. According to Reuters, Toyota isn't aware of any accidents, injuries or fatalities affecting the models. Some yet-unnamed Lexus models might also be affected.
The largest of the campaigns does not currently affect any US-market vehicles. About 802,000 units of the Toyota Crown Majesta, Crown, Noah and Voxy in Japan are being repaired to replace a seal that could leak in the brake master cylinder. Those already leaking get a new brake booster, as well, according to Reuters.
The only recall currently believed to affect the US is due to a problem covering approximately 759,000 vehicles with 423,000 of them here. The repair is to fix a faulty fuel delivery pipe that could cause a fire if the fuel leaks out. Unfortunately, we don't know which models it covers. Autoblog spoke to Toyota spokesperson Mona Richard and was told the information was still "under embargo." When exactly that embargo will lift isn't yet known, but we're on the case.

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

Toyota GT86 engineers explored shooting brake and sedan variants, are they still in the cards?

According to the Toyota UK blog, engineers for the automaker were so excited developing the GT86 coupe that they investigated producing a whole family of models based on the rear-wheel drive sports car. And at least one engineer - product chief Tetsuya Tada - still hopes it can happen, even if not everyone at Toyota is onboard. Tada: "Actually we tried to do this secretly but the executives found us out. They said: 'What are you doing? Will you please focus on the coupe.'"
Those mooted variants included both a four-door sedan and a shooting brake. Why? Aside from the pure excellence of a lightweight, brilliantly handling hatchback, Toyota was keenly aware of the fact that it may need to spread the cost of development out across several models. Tada says that's part of the reason why it was so easy to create the convertible. The company knew from the outset that a softtop version was in the cards, and built the machine's structure to accommodate having the roof sliced off.
Tada also made mention of the already-announced collaboration between Toyota and BMW. The engineer said that the GT86 was particularly helpful because it demonstrated just how successful a product conceived and designed by two different companies can be. While he didn't say exactly what Toyota and BMW are up to, it's clear the two are looking into a number of possibilities. It's an interesting read with a lot of