Find or Sell Used Cars, Trucks, and SUVs in USA

2023 Toyota Highlander Le on 2040-cars

US $29,400.00
Year:2023 Mileage:9122 Color: Blue /
 Graphite
Location:

Advertising:
Vehicle Title:Clean
Engine:2.4L I4 PDI Turbocharged DOHC 16V LEV3-SULEV30 265
Fuel Type:Gasoline
Body Type:4D Sport Utility
Transmission:Automatic
For Sale By:Dealer
Year: 2023
VIN (Vehicle Identification Number): 5TDKDRAH1PS043100
Mileage: 9122
Make: Toyota
Trim: LE
Features: --
Power Options: --
Exterior Color: Blue
Interior Color: Graphite
Warranty: Unspecified
Model: Highlander
Condition: Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. See all condition definitions

Auto blog

Lexus GX, Toyota Land Cruiser Prado facelifts leaked

Thu, 22 Aug 2013

The Lexus GX and the Toyota Land Cruiser Prado, which isn't sold in the US, have gone without visual updates since the current generation was launched in 2009. But what appear to be patent filing sketches and pictures of the sibling sports utility vehicles' mid-cycle updates have been leaked on a Russian Land Cruiser Club forum.
Major changes to the GX's front end will be made to incorporate Lexus' signature grille. Gone are the awkwardly shaped headlamps and the soft-looking triple-slat grille. The sketch shows the Lexus with a new bumper, lower-profile headlights and a more aggressive, angular grille with one more slat and a gaping lower air-intake opening. The vehicle's profile looks unchanged, but the rear bumper will be reshaped slightly to fit new, better-integrated horizontal reflectors.
The Toyota gets a handful of styling updates as well, including a new front bumper with higher-profile headlamps that look a bit out of place to us. The Prado's profile also looks unchanged, but the rear end gets restyled taillights and a reshaped license-plate enclosure.

Brand new cars are being sold with defective Takata airbags

Wed, Jun 1 2016

If you just bought a 2016 Audi TT, 2017 Audi R8, 2016–17 Mitsubishi i-MiEV, or 2016 Volkswagen CC, we have some unsettling news for you. A report provided to a US Senate committee that oversees the US National Highway Traffic Safety Administration (NHTSA) and reported on by Automotive News claims these vehicles were sold with defective Takata airbags. And it gets worse. Toyota and FCA are called out in the report for continuing to build vehicles that will need to be recalled down the line for the same issue. That's not all. The report also states that of the airbags that have been replaced already in the Takata recall campaign, 2.1 million will need to eventually be replaced again. They don't have the drying agent that prevents the degradation of the ammonium nitrate, which can lead to explosions that can destroy the airbag housing and propel metal fragments at occupants. So these airbags are out there already. We're not done yet. There's also a stockpile of about 580,000 airbags waiting to be installed in cars coming in to have their defective airbags replaced. These 580k airbags also don't have the drying agent. They'll need to be replaced down the road, too. A new vehicle with a defective Takata airbag should be safe to drive, but that margin of safety decreases with time. If all this has you spinning around in a frustrated, agitated mess, there's a silver lining that is better than it sounds. So take a breath, run your fingers through your hair, and read on. Our best evidence right now demonstrates that defective Takata airbags – those without the drying agent that prevents humidity from degrading the ammonium nitrate propellant – aren't dangerous yet. It takes a long period of time combined with high humidity for them to reach the point where they can rupture their housing and cause serious injury. It's a matter of years, not days. So a new vehicle with a defective Takata airbag should be safe to drive, but that margin of safety decreases with time – and six years seems to be about as early as the degradation happens in the worst possible scenario. All this is small comfort for the millions of people who just realized their brand-new car has a time bomb installed in the wheel or dashboard, or the owners who waited patiently to have their airbags replaced only to discover that the new airbag is probably defective in the same way (although newer and safer!) as the old one.

Tougher than steel: Wood pulp could make lighter auto parts

Tue, Aug 15 2017

KYOTO, Japan — The global push among carmakers to make ever lighter vehicles is leading some auto suppliers in Japan to turn to what seems like an unlikely steel substitute — wood pulp. Japanese researchers and auto component makers say a material made from wood pulp weighs just one-fifth of steel and can be five times stronger. The material - cellulose nanofibers — could become a viable alternative to steel in the decades ahead, they say, although it faces competition from carbon-based materials, and remains a long way from being commercially viable.> Related: Jay Leno drives the Renew cannabis car — hemp you can't dent Reducing the weight of a vehicle will be critical as manufacturers move to bring electric cars into the mainstream. Batteries are an expensive but vital component, so a reduction in car weight will mean fewer batteries will be needed to power the vehicle, saving on costs. "Lightweighting is a constant issue for us," said Masanori Matsushiro, a project manager overseeing body design at Toyota. "But we also have to resolve the issue of high manufacturing costs before we see an increased use of new, lighter-weight materials in mass-volume cars."A NEW PROCESS Researchers at Kyoto University and major parts suppliers such as Denso Corp, Toyota's biggest supplier, and DaikyoNishikawa Corp, are working with plastics incorporated with cellulose nanofibers — made by breaking down wood pulp fibers into several hundredths of a micron (one thousandth of a millimeter). Cellulose nanofibers have been used in a variety of products ranging from ink to transparent displays, but their potential use in cars has been enabled by the "Kyoto Process," under which chemically treated wood fibers are kneaded into plastics while simultaneously being broken down into nanofibers, slashing the cost of production to roughly one-fifth that of other processes. "This is the lowest-cost, highest-performance application for cellulose nanofibers, and that's why we're focusing on its use in auto and aircraft parts," Kyoto University Professor Hiroaki Yano, who is leading the research, told Reuters in an interview. The university, along with auto parts suppliers, are currently developing a prototype car using cellulose nanofiber-based parts to be completed in 2020.