2013 Subaru Forester 2.5x Premium on 2040-cars

Auto blog

Subaru's STI motorsport arm celebrates 30 years of going fast

The letters W, R and X are often featured on the trunklid of a fast, blue Subaru, but the other important letters for a Subaru are STI – standing for Subaru Tecnica International. The STI motorsport brand brings to mind '90s World Rally Championship victories and Impreza legends such as the wide-bodied 1998 22B, but the division is actually a bit older: STI is celebrating its 30 th anniversary this week. Founded on April 2, 1988, Subaru's STI started out with tuned Legacy sedans. Its first car was a turbocharged Legacy, the RS RA from 1989, available only in a limited 100-unit run of Ceramic White cars, not the 555 Sonic Blue Mica or World Rally Blue that later became almost synonymous with hot Subarus. The RS RA produced 220 horsepower, which was very good for 1989. In January of the same year, three STI-modified Legacy Turbos were used to first break the 50,000 km, then the 100,000 km FIA World Speed Endurance records, with the cars run for 20 consecutive days at Arizona Test Center. The average speed was 138.78 mph, for 447 hours, 44 minutes and 9.887 seconds. That's quite a bit of driving, even in two-hour shifts. The first STI-branded Subaru vehicle was the Japanese-market Legacy STI in 1992, and the Impreza WRX STI followed it two years later. For some time, STI vehicles were the stuff of Gran Turismo gaming for most Subaru enthusiasts, until STI arrived in the United States in 2004. The first U.S.-bound model was the 300-horsepower WRX STI, a Peter Stevens-designed "Blob Eye" facelift of the second-generation Impreza. So far, STI's respectable tally stands at three WRC championships, 47 WRC wins, four Nurburgring endurance wins and a Nordschleife production sedan lap record set last year. Regarding STI's 30th anniversary year's production cars, there will be a limited-edition WRX STI Type RA and a STI-tuned BRZ tS for 2018. View 51 Photos Related Video:

2016 Subaru Outback, Legacy recalled for driveshaft problem

The Basics: Subaru is recalling 3,251 examples of the 2016 Legacy built between Oct. 24, 2015, and Nov. 16 2015, and the 2016 Outback manufactured between Oct. 24, 2015, and Nov. 17, 2015. The Problem: The driveshaft could separate from the rear differential because the securing nuts aren't tight enough. If this happens, the driveshaft could hit the gas tank, leading to a fuel leak. Injuries/Deaths: Subaru spokesperson Michael McHale confirms to Autoblog there are no reports of accidents, injuries, or fires. The fix: Subaru dealers will inspect the nuts and tighten or replace them as necessary. If you own one: Subaru expected the recall to begin on December 10, so owners should receive notification very soon. Related Video: RECALL Subject : Drive Shaft May Detach From Differential Report Receipt Date: NOV 24, 2015 NHTSA Campaign Number: 15V794000 Component(s): POWER TRAIN Potential Number of Units Affected: 3,251 All Products Associated with this Recall Vehicle Make Model Model Year(s) SUBARU LEGACY 2016 SUBARU OUTBACK 2016 Details Manufacturer: Subaru of America, Inc. SUMMARY: Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential. CONSEQUENCE: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire. REMEDY: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

New Subaru concept crossover EV shown in walkaround video

Subaru held a technology briefing this week in Tokyo where it announced ambitious sustainability goals, but nearly lost amid the discussion of converting its fleet over to electricity was the unveiling of what appears to be an early concept version of a forthcoming battery-electric crossover. Thanks to the Japanese YouTube account LoveCars!TV!, we get a walkaround look. It appears to be Subaru’s version of the crossover EV it is jointly developing with Toyota, to be built atop a flexible platform that can accommodate multiple production vehicles from both brands. What weÂ’re shown is an athletic-looking crossover with its wheels pushed to the corners that borrows design elements, for better or for worse, from Cadillac, the Pontiac Aztek and the Tesla Cybertruck. Up front, the crossover borrows and exaggerates CadillacÂ’s signature squared-off corners and deep fog-light scoops that also reminds us of InfinitiÂ’s Q Inspiration concept from the 2018 Detroit auto show. It opts for narrow LED headlamps, and it notably omits any aesthetic concession to even a faux grille, save for a hexagonal shape outlined by the panel seams. Coupled with the black cladding on the lower bumper, the crossover's face has a certain Batman-logo shape to it. Moving around to the side, we see heavy black cladding — it doesn't appear to be standard plastic, since it reflects light — around the wheel wells, lending them a semi-octagonal shape that evokes the strongest comparison to the polarizing Cybertruck. Coupled with some interesting side creases, the cladding also gives the appearance that the wheel wells bulge out, and that the doors pinch inward, more than they probably do in reality. There are also no door handles or brakes, the side mirrors are rearview cameras and the windows are blacked out, so thereÂ’s nothing to divine about the interior and how far along that is in conceptualization. In back is where things get especially weird and Aztek-like, with a blunt and upright rectangular body panel making up the tailgate underneath a generously long, sloping rear window. ItÂ’s beveled at the top to tuck underneath the rear LED light bar, which stretches the length of the glass, and curved on each end to integrate with the sides. The LED treatment also dives down 90 degrees from the horizontal rear bar and then makes another sharp 90-degree jag to bracket the rear panel in hard-angled brake lights.