2014 Ram 1500 Tradesman/express on 2040-cars

Auto blog

Chrysler recalls 2013 Ram pickups, 2014 Jeep Grand Cherokee

Chrysler's spate of successful products is about to be marred by a trio of recalls. The Pentastar is recalling 51,477 Ram trucks and Jeep SUVs. According to the National Highway Traffic Safety Administration, there have been no reported accidents, injuries or deaths related to the affected vehicles.
The largest action covers the Ram 1500, which is seeing 45,961 trucks being recalled. Models built between June 26, 2012 and February 5, 2013 are being recalled due to a potential software issue in the electronic stability control. Apparently, the system can be randomly deactivated upon vehicle startup.
Chrysler is also recalling 4,458 2014 Jeep Grand Cherokee models. Covering everything but the SRT models, the potentially defective SUVs were built between January 14 and March 20, 2013. This recall focuses on "premium headlights," which means cars equipped with LED running lights. During the switch from the bright daytime running lamp setting to the low-intensity parking light setting, an electrical spike can cause one of the Jeep's computers to go into a safe mode, turning off the LEDs. This violates Federal Motor Vehicle Safety Standards.

Ram recalling 65k trucks for rear-axle heat treating

A problem with the rear axle has promoted Fiat Chrysler Automobiles to recall a selection of Ram trucks. The campaign affects 2015-16 Ram 1500 series trucks – specifically those manufactured between June 17 and September 28, 2015. All told, that amounts to over 65,760 units across the United States. The issue stems, according to the statements below, from the rear axle shaft. Some of those trucks may have not had those axle shafts properly heat-treated, which could cause them to fracture and separate from the wheel. And that, it should go without saying, could lead to a crash. FCA states that most of the vehicles in question are in dealer hands, but while the manufacturer says it is aware of one accident to have resulted from the issue, no injuries have been reported. The owners of the affected vehicles will be notified to bring their trucks in to their local dealership to have them inspected. If necessary, the dealership with replace the rear axle assembly. This recall follows three prior (but unrelated) ones, also issued for Ram pickups, that between them affected well over a million units. Related Video: RECALL Subject : Incorrectly Heat Treated Rear Axle Shaft Report Receipt Date: OCT 15, 2015 NHTSA Campaign Number: 15V661000 Component(s): POWER TRAIN Potential Number of Units Affected: 65,760 Manufacturer: Chrysler (FCA US LLC) SUMMARY: Chrysler (FCA US LLC) is recalling certain model year 2015-2016 Ram 1500 trucks manufactured June 17, 2015, to September 28, 2015. The affected vehicles may have been built with rear axles that were incorrectly heat treated. CONSEQUENCE: If the rear axle shaft was not properly heated treated, it may fracture and a wheel separation could occur, increasing the risk of a crash. REMEDY: Chrysler will notify owners, and dealers will inspect the vehicles and replace the axle assemblies, as necessary, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R59. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov. ### Statement: Heat-treating October 27, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 65,760 U.S.-market trucks – most of which are in dealer hands – to inspect and replace, as required, their rear axle shafts or rear axles.

Ram wants its midsize truck situation 'fixed soon'

The rumors of a midsize Ram pickup are like a metronome — sometimes in motion, sometimes dead. This week the rumor is alive, so reports Automotive News. Fiat Chrysler CEO Mike Manley admitted during an earnings call that the lack of a mid-sizer is "a clear hole in our portfolio," and that the Ram product development team is "focused on it." Puzzling that out means finding "a cost-effective platform in a region where we can build it with low cost and it still being applicable in the market." But he wants a solution found soon. During the product roadmap presentation FCA made in June last year, late CEO Sergio Marchionne said the middling pickup would be built in Mexico. That tidbit came after years of Marchionne saying the brand would get in the segment, only to have the idea shot down by Ram bosses. At the 2012 Detroit Auto Show, a year after the midsize Dodge Dakota went off the market, Marchionne said the brand would reinstate a new-generation Dakota, with a better-than-50% chance it would be unibody. In 2013, then-Ram president Reid Bigland said the chances were tiny because the numbers didn't add up. The two men got on the same page, in favor of, in 2014. In March 2016, Marchionne said, "I like that space a lot," and "It's a good space to be in." Exactly one month later, then-Ram CEO Bog Hegbloom said the idea was dead because he couldn't make a business case for it. Come early 2018, even Marchionne had joined the naysayers. He told Automobile, "We did not think it was necessary to re-enter that market after our last experience." The snag was, and remains, that a smaller truck has "a cost structure very similar to our Ram 1500. We have not found an economic way to get this done." Four months later, there's a midsize pickup on the product roadmap. Then, at this year's New York Auto Show, Ram Trucks boss Jim Morrison told us Ram had no plans yet for a smaller pickup, although the division continues to look at its options. Last September an Automotive News report forecast the truck to be built in Toledo alongside the Jeep Wrangler and Gladiator pickup. When Car and Driver asked for clarification about Toledo or Mexico, FCA pointed to Marchionne's comments referring to Mexico. It appears that's the angle Manley and his team are still trying to make work. The Saltillo, Mexico, assembly plant now builds Ram's heavy-duty trucks, but observers expect HD production to move to the U.S. to make room for the smaller pickup.