2014 Ram 1500 Laramie Longhorn on 2040-cars

Auto blog

Ram recalling 1,747 diesel trucks for short-circuit risk

Diesel-powered Ram owners, it's recall time. Fiat Chrysler Automobiles has announced a voluntary recall of 1,747 Ram 1500 EcoDiesels from model years 2014 and 2015. Why so few? Well, this campaign is limited to just rear-wheel-drive models. The problem, this time around, is with a battery wiring harness that will chafe against a bracket if it wasn't assembled properly. This chaffing can lead to a short, causing a loss of power (the best-case scenario) or even a fire (probably the worst-case scenario). Fortunately, FCA is unaware of any accidents, fires, or other injuries caused by short circuits. The affected vehicles were sold in both the US and Canadian markets, although the vast majority of the trucks, 1,697 to be precise, are here in the land of the free and home of the brave. The remaining 50 vehicles were sold in Canada, and were likely purchased by those crazy enough to drive a high-torque, rear-drive pickup in a country almost perpetually covered in snow and ice. Regardless of whether your truck has an illuminated dashboard warning light or not, FCA is encouraging drivers of the affected vehicles to report to dealers for a free service when they receive a recall notice. Scroll down for the official press release from FCA, as well as the bulletin from the National Highway Traffic Safety Administration. Statement: Wiring Harness September 9, 2015 , Auburn Hills, Mich. - FCA US LLC is recalling an estimated 1,747 trucks in the U.S. and Canada to inspect, reroute and replace – as required – their wire harnesses to prevent a potential short-circuit. An investigation by FCA US discovered a battery wiring harness may chafe against a bracket if assembly protocols were not followed. This condition is limited to vehicles equipped with diesel engines and 4x2 drivelines. Such a condition has the potential to cause a short-circuit, which may lead to power loss or fire. The Company is unaware of any related injuries, accidents or fires. The campaign is limited to certain 2014-15 Ram 1500 pickups. It is estimated there are 1,697 in the U.S. and 50 in Canada. Affected customers will be advised next month when they may schedule service, which will be performed at no cost. While the condition may not be present in every vehicle, FCA US urges customers to note the information on their recall notices and respond accordingly. Illumination of a dashboard warning light is among the indicators that the condition is present.

2019 Ram 1500 eTorque First Drive Review | The un-hybrids

Misinformation is already being passed around about the 2019 Ram 1500 eTorque – reports calling the new electrified version of the full-size half-ton pickup truck a hybrid and saying its eTorque system adds torque to the truck's engine increasing payload, towing capacity, and performance. Don't believe a word of it – this isn't a hybrid in the conventional sense of the word. eTorque does not increase the truck's power or capability. Instead, the system feeds in some electric torque at low RPM, which helps with fuel efficiency by spinning up the engine during start/stop operation, smoothing gearchanges, and harvesting some energy from braking – that's basically it. Ram is partially to blame for the hybrid confusion. Although the "h"-word does not appear anywhere on the truck or the vehicle's window sticker, the automaker has chosen to call eTorque a "mild-hybrid system", which implies that it might be able to propel the truck on electric power. But the Ram's small battery pack and single electric motor cannot – it's more similar to the original GM Parallel Hybrid Truck system than the later two-motor, two-mode hybrid system circa 2009. Also, eTorque applies power to the engine and the wheels briefly at very low engine speeds and during gear changes. These applications of power only last for fractions of a second at any given time, some as quick as the blink of an eye. So it's a labeling fiasco, but Ram's explanation of the eTorque system's operation and its benefits, which are significant, can also be perplexing. And the resulting discombobulation is unfortunate, because eTorque is clever, and it really does work. Earlier this week we drove two Rams with the system, one a V6 and one a Hemi, through Kentucky horse country, and came away impressed by its measurable contributions to the truck's fuel efficiency, drivability and smooth operation. We also interviewed Mike Raymond, the Chief Engineer on the Ram 1500, and Brian Spohn, Ram's Vehicle Electrification Manager, Powertrain Engineering, to better understand what it is and how it functions. How eTorque works Ram will offer the 3.6-liter 24-valve V6 with eTorque as the standard engine in most models. The V6 will not be available without eTorque, although we'd be surprised if it wasn't added to the menu at a later date.

Ram ramping up MI truck production, does deal with Texas Rangers

Thanks to a host of upgrades at the Warren Truck Assembly Plant in Michgan, Ram Trucks is boosting production of the already strong-selling Ram 1500 to build 28,585 more of them a year. That works out roughly to five more per hour, or an additional 100 per day. The major key to the improvements was redesigning 353 assembly workstations to allow employees complete their tasks more efficiently. According to Ram, the expansion was done to meet growing demand for the pickup.
These kinds of comprehensive changes can't happen over night, obviously. From the end of 2013 through the summer shutdown in August, the Warren Truck plant received automation tweaks in the body shop and upgrades to the color booths in the paint shop.
However, the biggest shift was working with "UAW-represented team leaders and operators" to examine every workstation for efficiency improvements. In that analysis, the company identified and altered over 100 problems that could have caused an injury. What really helped to boost the production rate so significantly was moving about 300 parts, or grouping them into kits for better ergonomics, and eliminating walks to grab tools. Once everything was done, about 63 percent of workers at the factory got updated training.