2011 Mitsubishi Lancer Gts Manual 2.4l 5 Speed on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Nissan plans to slash May car output in Japan by 78%

TOKYO — Nissan plans to slash the number of cars it produces at home in May by 78% from last year, as the impact of the coronavirus shakes the troubled automaker which has already been struggling with falling sales. As global automakers reel from plunging sales amid lockdowns imposed in many countries to curb the spread of the virus, the hit is particularly severe for Nissan, whose profitability has been deteriorating as it grapples with the turmoil that followed the ousting of former Chairman Carlos Ghosn. Nissan plans to manufacture around 13,400 vehicles next month, according to documents seen by Reuters, compared with nearly 61,000 units made in May last year. The cut represents a big hit to Nissan's plant in Kyushu, southern Japan, which the automaker plans to operate on a single shift for much of this month and all of next month, due to a lack of demand for the Rogue Sport SUV crossover model, according to the documents, which are not public. Output will decline 70% from initial plans to build around 44,800 units. In June, domestic production will be cut to 33,700 vehicles, a drop from around 63,700 units last year, and down 43% from a previous plan for around 59,300. Nissan declined to comment on its production plans. The automaker has stopped production at its plant in Tochigi, north of Tokyo, since early April, and plans to keep output suspended through the end of May. Periodic stoppages at Nissan's Oppama plant in Kanagawa Prefecture have been common since earlier this month. The coronavirus pandemic has piled urgency on Nissan's efforts to downsize, after two years of falling sales, deteriorating margins and depleting cash reserves has forced the company to restructure. Nissan's management has become convinced that the company needs to be much smaller and its latest recovery plan due next month will likely assume a cut of 1 million cars to its annual sales target, senior company officials told Reuters earlier this month. Automaking partner Mitsubishi, also suffering from a cut to demand for its cars, is planning to slash domestic output by nearly one-third over the next two months. As both Nissan and Mitsubishi struggle with tanking sales, production plans show one bright spot: Nissan is planning an increase in production of the Nissan Dayz minicar model, which Mitsubishi manufactures for Nissan for the Japanese market. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

Mitsubishi Evolution Final Edition goes out with a bang

The end of a long era - one we got to experience too little of - is just about at an end, and this car is its gravestone. The 2015 Mitsubishi Lancer Evolution Final Edition is the last breath of ten generations of Lancer Evos, three of which came to the US. Mitsubishi launched a Final Edition Evo X in Japan earlier this year, after teasing a 473-horsepower concept at the Tokyo Auto Salon, now it's our turn. Built on the lower GSR trim, our model gets 303 hp, a bump of 12 hp, and torque goes up by five pound-feet to 305 lb-ft. The bigger modification is arguably the fitment of Bilstein shocks wrapped in Eibach springs all around, plus two-piece Brembo calipers on the front axle, all of which come standard on the upper-level MR trim. Dark chrome Enkei wheels match the dark chrome front grille surround. Like the grille, other changes for the Final Edition appear to be ornamental: black aluminum roof, black interior with red accent stitching, and special badging. Mitsubishi is putting 1,600 on sale here, each one with a numbered plaque just ahead of the shifter for the five-speed manual transmission. A second badge makes an appearance on the decklid. Final Edition Evos come in one of four colors, new Pearl White, Rally Red, Mercury Gray and Octane Blue, and cost $37,995. That price puts it $700 above the GSR Premium trim, and $1,000 below the entry MR trim. There are two press releases below with more information. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Related Video: THE 2015 MITSUBISHI LANCER EVOLUTION FINAL EDITION: LIMITED-PRODUCTION MODEL BIDS FAREWELL TO LEGENDARY SPORTS SEDAN • The Final Edition is based off the current GSR model featuring new enhancements and increases to horsepower and torque • Only 1,600 units will be sold in the U.S. market, each marked by a numbered plaque CYPRESS, Calif. Oct. 5, 2015 – Mitsubishi Motors North America, Inc. (MMNA) today announced the details of the limited-production 2015 Lancer Evolution Final Edition. Arguably the originator of the four-door sports car genre, the Lancer Evolution has seen ten generations – three of which were sold in the U.S. over 12 years. To send it off in style, Mitsubishi Motors will offer 1,600 numbered Final Edition models to the U.S. market with a MSRP of $37,995. The Lancer Evolution Final Edition is based off the current GSR model, with exterior and interior enhancements not previously offered on the GSR.