2007 Mini Cooper S Convertible! Heated Seats! Harmon Kardon! Power Top! L@@k! on 2040-cars

Auto blog

Mini Minor to be co-developed with Toyota

It was back in 2011 when Mini first showcased the prospect of an even smaller hatchback with the Rocketman concept at the Geneva Motor Show. In the nearly four years since, parent company BMW has hemmed and hawed on the possibility of putting it into production, but the latest word from Europe has it that the project is a go. According to Automobile magazine, Mini is realigning its product portfolio into five pillars: the essential hardtop we've already seen (available in two/three- and four/five-doors), the convertible, the upcoming new Clubman wagon (coming this summer with full-size auxiliary suicide doors on both sides), the next-gen Countryman crossover in 2016 and two new model lines. One will be the production version of the Superleggera roadster concept, earmarked for 2018. The other will be the Minor, a smaller city car reviving a long-gone model name and presaged by the aforementioned Rocketman concept. But for that last one, Mini won't go it alone. To develop the mini Mini, BMW will reportedly turn to its partnership with Toyota. The relationship is already set to yield a new Supra and Z4 and share fuel cell and other technologies. But this would broaden the partnership to include a small hatchback. However rather than use the existing (or next-gen) Aygo, which is already built under joint venture with PSA Peugeot Citroen (with which BMW previously had a joint engine venture), word has it that the BMW and Toyota will develop a new platform for the project – one that will be used by both partners. The new product plan doesn't leave much room for the Mini Coupe and Roadster (which have already been discontinued), for the Paceman three-door crossover (which will suffer the same fate) or for the projected seven-seater minivan. But the addition of the new Superleggera roadster and super-mini Mini aren't likely to leave us wanting for either. Related Video:

Mini fini: The Mini Clubman passes into British motoring history

Au revoir, Clubman. The veddy British Mini model that found a loyal following in the UK and elsewhere for more than a half-century has folded its spilt rear “barn doors” for the final time. The ultimate Clubman — assuming there wonÂ’t be another sequel, and Mini says there won't — rolled off the production line Monday at Mini Plant Oxford in England. The Mini “estate” version bows out after 17 years of build at Oxford and more than a half-million units churned out for deliveries to more than 50 countries. The heritage of the Clubman — and of most Minis — is worth recalling because the brand has spawned such affection among its fans. One has to deep-dive back to the early Sixties, when MiniÂ’s owner, British Motor Corporation (BMC), introduced two estate versions of the original Mini: the Austin Seven Countryman and Morris Mini Traveller. In 1967, the characteristics of existing Mini wagons were combined to form the first Clubman. lt was axed in 1982 — after it was once renamed as the 1000HL — and the Clubman wouldn't return until 2007, with the brand then under the auspices of BMW. Modern vehicle safety standards presented a challenge for those rear doors. “We needed to ensure that both doors would always open fully without obscuring the rear lights, which was a legal requirement,” said Guy Elliott, who was part of the development team for the doors at the time. The reborn Clubman was updated in 2015 for a second generation. It adopted Mini's signature circular daytime running lights, a feature still seen today, and ditched the unusual rear doors for a more conventional setup. Last year Mini launched the “Final Edition” of the car, with a special grille and alloys and limited it to a run of 1,969 units, paying homage to the launch year of the original. The BMW Group says it expects to invest about $750 million in the next few years in realigning the Oxford plant to accommodate assembly space for the upcoming electric Aceman crossover and new Cooper variations later this year.

Meet Vini, the V8-powered second-generation Mini Hardtop

There are several ways to extract horsepower from a Mini Hardtop, and most are far more straight-forward than squeezing a V8 engine under the clamshell hood. And yet, at the request of a client, England-based EDM Racing is well into the process of doubling the retro-styled hatchback's cylinder count while making it rear-wheel drive. Amusingly called Vini, the V8-powered Mini started life as a 2007 Cooper S. It had a little over 100,000 miles on its odometer when David Power, the managing director of suspension bushing expert Powerflex, instructed EDM Racing to prepare it for an improbable engine swap. As mechanics stripped it to the bare metal, Power sourced a 4.0-liter, 415-horsepower V8 and a matching seven-speed automatic transmission from an E92-generation BMW M3 and began figuring out how to make it fit into a city-friendly hatchback delivered new with a 172-horsepower, 1.6-liter four-cylinder engine. Installing the new drivetrain directly behind the front seats would have likely been the easiest solution from a packaging standpoint, but the team decided to keep the front-engined layout. The conversion consequently required chopping out significant chunks of the Hardtop's firewall and floor, so EDM Racing started by designing and welding in a roll cage to maintain the car's structural integrity. The firm then installed modified front and rear subframes from a Subaru Impreza to keep the four wheels in their original position, or as close to it as possible. Power stressed he wants Vini to look nearly stock, especially when it comes to its track width, meaning punching out the wheel arches Renault 5 Turbo-style was out of the question.  The V8 fits surprisingly well in the Mini's engine bay, and it keeps the car's weight distribution in check. Power originally considered using a Subaru-built flat-four or a straight-six from an earlier M3, but both would have put too much weight ahead of the front wheels. Installing the automatic transmission was more difficult, however. "Making it all work in an OEM fashion will be a challenge for sure, but no more so than the most galling part of the project so far: Chopping out a transmission tunnel wide enough to accept the Getrag. I was aware of the dangers associated with cutting too much away and removing integral strength from the shell in the process, hence why we tackled the job in set stages and with the cage [installed]," EDM Racing's Elliott Dunmore explained.