1953 Mercury Ford Monterey Woodie Wagon on 2040-cars

Auto blog

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"

Ford finds flex-fuel engine design plays big role in emissions output

How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.

Ford recalling 126,000 Fusions and Milans over wheel separation concern

Ford has announced a recall of certain Ford Fusion and Mercury Milan vehicles after an investigation by the National Highway Traffic Safety Administration. A total of 128,616 2010 and 2011 models equipped with steel wheels may have been manufactured with wheel studs that could crack and split over time. If that happens, the vehicle may experience a wheel separation.
According to The Detroit News, the company is aware of a total of 30 wheel separation incidents, one of which occurred on the front of the vehicle. Even so, no injuries have been reported as a result of the defect.
The problem apparently stems from the fact that the mounting pads on the vehicles' steel wheels may have been faulty from the factory. In addition, the wheel mounting face on rear disc brakes may not have been installed properly. Ford will inspect the rear disc face and replace them as necessary. In addition, the company will replace all of the vehicle's wheel studs free of charge. Head to the NHTSA website for more information, and click past the jump to view the full recall notice.