1950 Mercury Capri Custom Sedan Convertable Custom on 2040-cars

Auto blog

The 1965 Ford Mustang could have looked a lot different

The 1965 Ford Mustang is unquestionably an automotive design icon, and nearly every generation of Mustang has some connection to that original car. Because it's such a universally-known vehicle, we were amazed to see all the different designs that were being considered. Head of Ford's archives Ted Ryan recently shared photos of design proposals for the original Mustang on Twitter that he and Jamie Myler found, and we reached out to them to find out more. As Ryan initially noted, the photos were taken on August 19, 1962, and they are proposals for the Ford Mustang. Apparently Ford had committed to doing a Falcon-based youth-oriented car at this point, and it did have plans to launch the car in 1964 for the 1965 model year. But after having little success with early design proposals, the company asked all of its design studios — the Advanced Studio, Lincoln-Mercury Studio and Ford Studio — to submit proposals. With only about two years before the planned launch, Ford was understandably short on time, and it's believed that the studios only had a month to create and present these designs. Lincoln-Mercury design proposal View 8 Photos The majority of the designs, a total of five, came from the Advanced Studio, and part of this was because they already had a couple of concept designs in reserve it could present. Two other models representing three design possibilities came from Lincoln-Mercury, and just one model with two options came from Ford. The Advanced Studio proposals are shown in the gallery at the very top of this article, and the Lincoln-Mercury and Ford proposals are in the gallery directly above this paragraph. The Advanced Studio's most radical design is the one that was clearly related to the Mustang I concept that would be shown later that year with huge wraparound rear glass, turbine-inspired bumpers and enormous side scoops. The other proposals from the studio were more conservative, featuring simple lines, grilles reminiscent of the Falcon, and one even borrowing the jet-thruster-style taillights made famous on the Thunderbird. Lincoln-Mercury had some impressively bold designs, particularly its fastback that had buttresses to extend the shape all the way to the tail. This car had two different side trim possibilities. The other Lincoln-Mercury design was toned down a bit, but had two interesting possibilities for side detailing, as well as some crisp, low-profile tail fins.

Ford recalls 600,000 older-model sedans for braking issue

Ford is recalling 600,166 older-model Ford, Lincoln and Mercury vehicles over an issue that could affect braking and increase the risk of a crash. The safety recall covers certain Ford Fusion, Mercury Milan and Lincoln MKZ sedans from the 2006 through 2010 model years that were built at Ford’s Hermosillo Assembly Plant in Mexico between Feb. 22, 2006, and July 15, 2009. Ford says a valve that is normally closed inside the hydraulic control unit may get stuck in the open position or be slow to close, which could make it harder to engage the brakes and increase risk of a crash. Ford says itÂ’s aware of 15 reports of accidents and two injuries possibly related to the issue. Dealers will inspect the hydraulic control unit for signs of the problem and replace it, if necessary. The dealers will pressure-flush the system with brake fluid and replace the reservoir cap with a new one. Ford is also issuing a small recall of 33 of its 2020 F-150 trucks in the U.S. and 51 in Canada over potentially damaged spare tires. It says the bead area on the tires may have been damaged when it was mounted onto the wheel assembly, leaving it vulnerable to corrosion, separation of the bead wire and ultimately a rapid loss of air pressure and detachment from the wheel. Dealers will replace the spare tire. Affected vehicles were built at the Dearborn Truck Plant from Nov. 10-21 of this year.

NHTSA investigating Ford's solution to May 2014 power steering recall

The National Highway Traffic Safety Administration is investigating a complaint that Ford's response to a May 2014 recall of the 2008 to 2011 Ford Escape and Mercury Mariner doesn't quite go far enough to solve a troubling power-steering problem. Roughly a year ago, Ford recalled nearly a million vehicles after it was found that a problem with the torque sensor's communication with the power steering control module could cut steering assistance for drivers. While manual steering would still be available, the problem was enough to ask drivers to report in to have the PSCM inspected, and if necessary, replaced (along with the torque sensor, or in dramatic cases, the entire steering column). That would only happen, though, if trouble codes were being thrown. If there weren't any problems, dealers were told to simply update the PSCM's software so that any issues between it and the torque sensor would simply throw a visual and audio warning – power steering would still be maintained. The petitioner claimed that following the recall work, he still experienced a problem with the torque sensor. According to NHTSA, a claim was made that Ford didn't go far enough in its solution to the problem, and that "the software update itself may in fact cause further issues with the affected vehicle's power steering, causing it to fail, and ultimately requiring replacement of the torque sensor or entire steering column." The petition was filed in early February and is now officially being looked into by NHTSA.