1970 Mercury Montego(cyclone Spoiler Clone) 302v8 3-speed~rock Solid~super Clean on 2040-cars
Roscoe, Illinois, United States
Mercury Montego for Sale
1973 mercury montego mx brougham 5.8l
2005 mercury montego runs & drive can drive it home
2006 sedan used v6 3.0 liter 6-spd automatic fwd leather red(US $11,882.00)
Beautiful original 1973 mercury montego mx brougham survivor(US $6,700.00)
No reserve nr 2006 mercury montego awd 1 owner good tires clean runs fantastic!
2006 mercury montego premier sedan 4-door 3.0l(US $6,250.00)
Auto Services in Illinois
Wheel-Go Camping Inc ★★★★★
Wellfit Parts International Corp ★★★★★
Weber Automotive ★★★★★
Top Value Auto Repair ★★★★★
Swedish Car Specialists ★★★★★
Streit`s Auto Repair ★★★★★
Auto blog
Fitting Retirement: Grand Marquis last Mercury off the line
Wed, 05 Jan 2011The signs have come down and retail production ended back in October of 2010. Now, the very last Mercury model has rolled off the assembly line. This last Mercury somewhat fittingly takes the form of a Grand Marquis reporting for fleet duty. It was built at the St. Thomas plant in Ontario, Canada, which is the same facility that continues to produce the Ford Crown Victoria and Lincoln Town Car for fleet and livery duty.
St. Thomas' days are numbered, however, as the factory is slated to close on August 31. When it goes, the Panther platform is likely to follow. So long, and thanks for all the fish memories.
[Source: Autoweek]Read | Permalink | Email this | Comments
NHTSA closes rollaway investigation into 1.56M Ford SUVs
Mon, 11 Mar 2013It's taken four years of study, but the National Highway Traffic Safety Administration has finally closed the books on its investigation into rollaway accusations surrounding 1.56-million Ford SUV models.
The probe, which centered on the 2002-2005 Ford Explorer, 2002-2005 Mercury Mountaineer and 2003-2005 Lincoln Aviator, ends without the federal agency calling for a recall. According to The Detroit News, the investigation was closed due to a "low number of complaints" - NHTSA documented 180 such complaints that resulted in 14 crashes and six minor injuries, but the number of incidents have been slowing. The suspected defect rate for the trucks' automatic transmissions was found to be 4.4 per 100,000 units, and the brake-shift interlock mechanism failure rate was judged to be even lower at 3.4 per 100k.
Ford finds flex-fuel engine design plays big role in emissions output
Mon, Jan 6 2014How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.










































































