1988 Mazda Rx-7 Convertible Clean In And Out!!!! No Reserve!!!!!!!!!!! on 2040-cars

Auto blog

The redesigned 2019 Mazda3 moves way upscale

Mazda didn't lie — the 2019 Mazda3 is a gently reworked production version of the Kai concept shown at last year's Tokyo Auto Show. In hatchback and sedan forms, you'll still quickly peg this a Mazda3. The dimensions barely change: The wheelbase grows by an inch, but the hatchback width and length carry over, while height decreases by an inch; the sedan is the same width but 3.2 inches longer and 0.7 inches lower. Nevertheless, the look and details have evolved throughout, yielding a much more potent and piercing hatchback, and a more sophisticated, accomplished sedan. Instead of using hard shoulder and swage lines to "draw" contour onto a flat profile, Mazda designed a car with contours that create real shoulders and hips. Shedding the illusion of surface depth for reality redefines the look and presence of the Mazda3. The new model erases the hash of lines and embossed panels in back of the current car so that the S-curved hatch has only its shutline for framing. After that, the highlights enhance the theme. On either side of the larger grille, single-lens headlamps get new accents; instead of a just plain silver bar, streaks of amber turn signals decorate the more dimensional units. The contoured taillamp housing holds highly structured, highly embellished twin circles that probably look even more sinister at night. On the sedan, those naughty taillights are surrounded by a refined rear valance with a more angled, muscular lip along the trailing edge. It's the same inside, a design based on results of Mazda's in-depth studies of human mechanics. The flatter instrument panel stresses clean lines along the horizontal. Trimmer steering wheel spokes with silver buttons line up with the central span across the dash housing the climate control buttons and vents. The new shift panel sits higher and more forward, making it easier for the driver to move a hand from the steering wheel to the lever. To raise perceived luxury, the center tunnel trim is a clear layer laid over a laser-engraved black layer, said to produce a "look of deep transparency," and similar to the effect found on the new BMW X5 and X7. The cupholders are now in front of the shifters, and the armrest is longer. There's no mention of that digital gauge cluster that leaked earlier this year, though. Buyers who opt for fabric will get a new "Greige" hue, a mix of gray and beige. Mazda designed a new leather grain with creases of varying depths and shapes depending on where it's placed.

Mazda to use rotary engine as a range-extender with its first electric vehicle

There's more news from Mazda at the Tokyo Motor Show, where the brand made a big splash, including new developments in its never-ending rotary engine saga. First, Mazda execs confirmed that the Japanese automaker will bring back the rotary engine as a range-extender and battery juicer for its first electric vehicle in 2019. But secondly, the company won't have a rotary-powered successor to its RX-7 and RX-8 sportscars in time for the company's centennial anniversary in 2020. Autoblog previously confirmed that Mazda is planning to have an EV in 2019 that will be available in both pure electric and range-extending versions. Now, the Australian website Motoring reports that the global EV will feature a powertrain similar to the experimental Japan-only Mazda2 (Demio) EV, which used a single-rotor engine as a generator to power the battery pack and increase its driving range. The publication says Mazda plans to release a series of plug-in hybrids based on existing models around 2020, then a pure electric car co-developed with Toyota and Denso in 2021 as part of the EV Common Architecture Spirit Company joint venture. A Mazda spokesman tells Autoblog the company couldn't confirm any details about future products. Meanwhile, enthusiasts shouldn't wait for a rotary-based production version of Mazda's RX-Vision concept from 2015. Motoring cites two executives who explain that the company simply lacks the capital necessary to invest in developing the new model in time for its 2020 centennial. Mazda debuted its rotary engine 50 years ago in the Cosmo Sport in part as a way to stand out from its larger Japanese competitors. The engine, which uses a spinning three-tipped rotor in place of pistons, is smaller and lighter than conventional piston engines, with a greater power-to-weight ratio and quieter, smoother operation. But it delivers less fuel economy and higher emissions — two weaknesses that could be improved via a stop-start system Mazda has developed, based on a pair of U.S. patents. The company has also been hard at work developing its next-generation Skyactiv-X engine, which uses highly precise combustion ignition technology to deliver significant gains in fuel economy and power.Related Video:

Mazda plans a new crossover for 2021

If Mazda is going to increase sales, it's going to need more crossovers. According to company CEO Masamichi Kogai, a new crossover that won't cannibalize sales of the CX-3, CX-5, and CX-9 is coming in 2021, to be built at the new U.S. factory Mazda is building in partnership with Toyota. The plant will be able to build 150,000 vehicles per year, and that full capacity will be reserved for the new CUV. With 112,235 units sold, Mazda's best-selling vehicle in the United States last year was, not surprisingly, the CX-5. With that in mind, it seems a safe bet that the new crossover will be a replacement for the discontinued CX-7 to slot above the CX-5 and below the CX-9. Kogai told Automotive News that the vehicle will be designed for America and built exclusively in the States. "We are actually going to introduce a totally new and different type of SUV," said Kogai. We don't know exactly what that means, but we hope the new model line follows Mazda's tradition of crossovers that are more fun to drive than their main competitors. Related Video: