6 Spd Manual**alloys**bose**fog Lamps**fla Car** on 2040-cars

Auto blog

Confirmed: Mazda Miata gets more power, higher redline, telescoping wheel

Our friend over at Road & Track, Bozi Tatarevic, has a keen nose for stuff just like today's Miata news, and he spotted an article by the Japanese car magazine Car Watch that details Mazda's upcoming updates. Car Watch actually got to drive the car, too. There's a lot to go through, but the highlight has to be confirmation of what we told you earlier this year about a significant power bump: The Miata will indeed get an increase of 26 horsepower, from 155 to 181. But the power's not the whole story. Mazda has increased the redline from 6,800 RPM to 7,500. It's not clear at this point where torque and power peaks are in the rev range, or how these changes affect low-speed drivability, but more revs are almost always a good thing and aren't likely to detract from the roadster's fundamental goodness. Car Watch reports that lighter pistons and connecting rods are fitted to help reduce rotational mass in the 2.0-liter inline-four. Some valvetrain changes were needed to support the higher redline, mainly stiffer valvesprings to prevent valve float. Mazda also changed the shape of the valves and optimized the intake ports to breathe better at higher RPM. The inner diameter of the exhaust ports were increased to flow better through a new muffler better tuned to the engine's new operating range. This confirms and gives a little more detail to what we reported earlier based on a leaked document from Mazda Canada. Car Watch also confirms that the revised Miata will get a low-inertia dual-mass flywheel, which should help absorb some vibration, noise and harshness from the higher-revving engine without losing too much of the directness that a single-mass flywheel provides. Mazda usually gets stuff like this right, so while we won't know until we get a chance to drive it whether the DMF feels "right," we're not too worried about it. There's also a telescopic steering wheel, a first in any Miata, which has a range of about 1.1 inches. That doesn't sound like much, but it should help folks with longer legs reach the wheel without having to crank the seat forward. Interestingly, Car Watch reports that the telescoping wheel was opposed by some in the company seeking to save every fraction of an ounce of weight, and to get it through, the company apparently had to change some of the material in the upper steering column from steel to aluminum to satisfy the weight-conscious. Little details like these are fantastic.

Japanese students turning Mazda CX-5 into Dakar Rally-ready off-roader

Students at Japan's Nihon Automobile College (NATS) are transforming a first-generation Mazda CX-5 into a full-blown off-roader that looks ready to compete in the Dakar Rally. Named CX-Runner, the one-of-a-kind model will make its debut at the Tokyo Auto Salon opening its doors in January 2020. The Tokyo Auto Salon is the Japanese equivalent of the annual SEMA show, so anything goes under the bright lights. NATS students began the CX-Runner project with a used 2012 CX-5 and seemingly set out to leave as few original parts as possible. While the project isn't finished yet, a sketch released by the school suggests the crossover will receive wheel arch extensions, an external roll cage, a beefier suspension, and a shorter front bumper that increases the approach angle.  Photos published on the school's official Facebook page show the project is moving along nicely. The body extensions are made with a composite material that looks like Kevlar, and fitting the rear wheel arches required sealing the back doors, which is fine; the CX-Runner will be a two-seater. We don't know if students are planning to make changes to the CX-5's powertrain yet, but a thick skid plate will protect whatever is under the hood from expensive impacts with obstacles encountered off-road. nats-mazda-cx-runner-project-1 View 3 Photos The Tokyo Auto Salon will open its doors on January 10, so the students have time to finish the custom-made body kit, install the suspension, paint the CX-Runner, and fit the roll cage. They're not just doing this for fun, though. NATS began offering a customizing class in 1998, and building a tuner car is one of the requirements aspiring builders need to fulfill in order to graduate. With that in mind, it's no surprise that NATS will again have a big presence during the 2020 edition of the Tokyo Auto Salon. In addition to the CX-5 off-roader, its students are building six custom cars including a Nissan 370Z roadster wearing front and rear fascias sourced from a GT-R, a Toyota 2000GT-inspired convertible based on the Suzuki Cappuccino kei car from the 1990s, and a four-door, five-seater Toyota 86 built on Camry bones but powered by the coupe's flat-four engine. Relate Video:

2014 Mazda6 i-Eloop to net 40 mpg hwy, 28 mpg city

Even before Mazda unveiled the 2014 Mazda6, it had introduced its innovative, non-hybrid i-Eloop (Intelligent Energy Loop) brake regeneration system. This technology converts kinetic energy into usable electricity using the alternator, a DC/DC converter and a capacitor mounted just behind the front fascia. During deceleration, the alternator captures energy that is then stored in the capacitor, which can later be used to directly power electric devices like climate control and audio systems. When i-Eloop power is used, it reduces the load on the engine and helps to conserve fuel.
Now available on the Mazda6, i-Eloop is only available on the $29,695 Grand Touring trim level as a part of the $2,080 GT Technology Package, meaning that buyers desiring i-Eloop will have to spend at least $31,775 (not including destination). The added price of this technology should be worth it for those looking for optimal fuel economy as the i-Eloop, combined with the package's active grille shutters, will bump the sedan's fuel economy numbers up to 28 miles per gallon city and 40 mpg highway - both are improvements of 2 mpg over the standard Mazda6 Grand Touring. The GT Technology Package also includes a Sport mode, lane departure warning, high beam control, radar cruise control and forward obstruction warning - the latter two technologies are currently offered in a $900 package that is being discontinued.
i-Eloop will eventually be offered on other Mazda products including the 2014 Mazda3. Scroll down for the official press release on the Mazda6's fuel-saving i-Eloop technology.