4dr Sdn Auto I Touring Mazda Mazda3 I Touring New Sedan Gasoline 2.0l 4 Cyl Engi on 2040-cars

Auto blog

Mazda 16X rotary engine two years away, will arrive in all-new model

We last reported on Mazda's next-generation rotary engine project in June of 2012 when the automaker built its last Renesis-powered RX-8, but rumors of this new engine's development had been around way before that final car left the production line in Japan, last year.
We now have enthusiastic confirmation that this next-gen rotary engine is really and truly going forward. It is still referred to as 16X and has several priorities. First is to lower fuel consumption compared to the RX-8's engine, while still making gains in terms of performance. The second is to reduce the burning of oil that was happening at the highest revs. And the third and final priority, and perhaps most key for enthusiasts, is to give the powertrain a big torque upgrade.
What we were told by a Mazda USA insider (while we are all here together at the festivities in Monterey) is that the first application of the new 16X engine will be happening in two years' time in an as yet undisclosed new model. Oh, the mind races to our eternal Mazda wish list...

Mazda Skyactiv-X Review | The revolution begins with a squeeze-bang

The matte black Skyactiv-X prototype looks like a rough Mazda3, perhaps reconstructed after a bad wreck by an over-enthusiastic owner of a spot welder and lots of gaffers' tape. Ribbed ducts poke out of the dash sending two breaths of conditioned air to no one in particular. Even its revolutionary engine, the thing we're here to experience, is entombed in a massive, nondescript cover to mask its unseemly noises. It's a wild, strange way to meet a very unconventional vehicle that promises diesel-like fuel economy, a wide torque band, and an exotic method for burning less gas than ever before. It takes a few hours for Mazda's engineers to explain the fundamental principles of operation. For more detail, read our Skyactiv-X Spark Controlled Compression Ignition explainer, but here's a very brief overview. Skyactiv-X marries some traditional gasoline engine characteristics with a novel form of compression ignition called SPCCI. The key for Skyactiv-X is to use very high compression in the cylinder and an extremely lean fuel-air mixture. Squeezed right to the cusp of getting hot enough to blow up all on its own (which is very hard to predict), a squirt of extra gas and a spark interject to cross that compression-ignition threshold in a controlled and predictable manner. See the animation below: That takes a few essential components to get just right. One is a massive amount of computer processing power and some pressure sensors in the individual cylinders, because the ambient conditions change how and when these things happen. Skyactiv-X uses a clutched supercharger to pump in additional air when needed to nail the mixture precisely, and high-pressure injectors to get the low ratios of fuel to disperse properly in the chamber. And since it operates like a conventional gasoline engine sometimes, it uses valve timing to lower the very high compression ratio so it doesn't reach combustion ignition in that mode. In practice, the Skyactiv-X runs in compression ignition mode most of the time. In practical terms, that means it drives like a torquey gasoline Skyactiv engine. The torque curve is broad and flat — diesel-like in that respect. That also means it can get away with using a six-speed transmission and a lower final drive for better response. There's enough grunt and economy together that Mazda can let the engine spin faster — at 60 mph, it's running at roughly 1,000 more RPM than a similar gas engine, with greater efficiency.

Mazda's new Mexican plant capacity rises to 230,000

After the turmoil of last year, 2013 is getting off to a much better start for Mazda. The company has issued a release indicating that the forthcoming plant in Salamanca, Mexico has had its production capacity raised even though it isn't scheduled to go online until March 2014. The original plans called for a 140,000-unit capacity, 90,000 of that allotted for the Mazda2 and Mazda3, the remaining 50,000 for a small car Mazda would build for Toyota that would be based on the Mazda2. The new plans call for raising that by 90,000 units to a total of 230,000 units within two years, by the end of March 2016, and it looks like it will all go toward Mazda production to satisfy growing demand for Skyactiv vehciles. The Mexican plant's opening will be the return of Mazda manufacturing to North America, after Mazda6 production was moved back to Japan last year.
More good news for the company is that it projects 10 billion yen ($114 million) in net income for the financial year that will end in March. That would be a welcome turnaround from the 100-billion-yen loss in the previous financial year, part of a series of three annual losses in a four-year span.
You'll find the press release with the factory update below.