Mx-5 Manual Convertible 2.0l Cd Rear Wheel Drive Power Steering Abs Bucket Seats on 2040-cars

Auto blog

Mazda files patents for a sequential twin-turbo setup

Mazda has a history of interesting engine technologies, from yesterday's rotary engine to tomorrow's compression ignition engine, and new patents show it still may have some internal combustion tricks up its sleeve. The one on display in these patents isn't especially new in concept, though. A sequential twin-turbocharger setup is something Mazda itself used on the third-generation RX-7. But it's something we haven't seen much of lately. It looks like it could have some possible advantages over older sequential systems, and it has some potential advantages for enthusiasts. First a quick and dirty primer for what makes a sequential twin-turbo system distinct from other twin-turbo systems. In many twin-turbo engines, there are simply two turbos that work together as one bigger turbo. They're the same size, and they spool up at the same time. With a sequential setup, at low rpm, a smaller turbocharger is spooled up first at low-rpm for quicker throttle response, and as the rpm and exhaust pressure increases, a valve opens up that allows a larger turbocharger to also spool up and provide high-rpm boost. That's basically how the Mazda design shown above functions. A big flap blocks off the larger turbocharger exhaust inlet, channeling all the exhaust to the smaller turbo. When more exhaust is available at high rpm, it looks like that flap opens up to spool up the big turbo, too. What's interesting here is that the way the turbochargers are packaged takes up less space than past systems. It looks like both turbos are contained in one unit that shares the same exhaust outlet, meaning the exhaust manifold could be kept simple and compact. In fact, the piping for compressed intake air could also be shared, reducing the amount of piping, which would further decrease the amount of materials and possible failure points. There are a number advantages of making this system smaller. The potential applications of the system are much greater, since it could fit in smaller cars with smaller engine bays. Making the system smaller also means that there won't be as much weight, which is important from both fuel economy and performance standpoints. Finally, the smaller setup likely uses fewer materials, which could make the system cheaper and thus easier to offer on a wider range of vehicles, or at least more profitable for Mazda.

Next Mazda MX-5 Miata headed for 2015 Chicago debut

Twenty-six years after it was introduced at the 1989 Chicago Auto Show, the much anticipated fourth generation Mazda MX-5 Miata will meet the press at the 2015 Chicago show. A piece in Autocar refines some of the details on the larger, lighter Miata that a Mazda insider has said will be "our best-looking car ever."
The company has relented on the quest for the metric tonne, the 1000-kilogram (2,200-pound) target too difficult to achieve in light of cost constraints. You can still expect it to lose a generous dollop of weight - Autocar says a curb weight of 1,100 kg (2,420 pounds) will still make it the lightest in its class. And Mazda will be stressing a fun driving experience through light weight and a modest amount of naturally-aspirated horsepower. Engine capacities of 1.5 and 2.0 liters are expected. Sounds familiar (and good), right?
The Miata's interpretation of Kodo design will be veer from that found on the Mazda3 and Mazda6, with "very clean and simple" lines marking out "more muscular proportions" and elongated bodywork on a longer wheelbase. A stretched engine bay will make room for the current Skyactiv engine and perhaps the future Skyactiv 2 powerplants, initial reports suggesting there could be a 30-percent increase in fuel economy from the moment it arrives.

Mazda6 diesel delayed until April

Diesel enthusiasts waiting on the new Skyactiv-D-powered Mazda6 will have to wait a bit longer. The shapely fuel-efficient four-door has just had its North American launch pushed back to April, due to delays in emissions testing. Mazda had originally planned to launch the Mazda6 diesel before the end of this year, making the four- to five-month delay a rather serious one.
Mazda's senior vice president of US operations, Robert Davis, told Mazda employees in a letter obtained by Automotive News that, "final certification testing - the results of which are looking encouraging - is taking longer than we had initially expected." Following this letter, Mazda made an official announcement:
"The on-sale date for Mazda6 SKYACTIV-D clean-diesel has been moved to late-Spring 2014, to accommodate final emissions testing and certification. We are pleased with the ongoing development and are excited to launch this much-anticipated vehicle in North America. 2014 Mazda6 sales continue to exceed both our expectations and our production abilities, and supplies of the car are short at dealers across the U.S. More information on the SKYACTIV-D clean diesel Mazda6 will be available closer to the on-sale date."