2021 Mazda Mx-5 Miata Grand Touring on 2040-cars

Auto blog

Mazda recalling 190,000 CX-7s due to rusty ball joints

UPDATE: This post has been updated with additional information from Mazda. The Basics: Mazda is recalling 190,102 Mazda CX-7 crossovers built between February 14, 2006, to May 9, 2012 – model years 2007 through 2012. The Problem: Water can sneak in between the suspension ball joint fittings. If snow and road salt are common in your neck of the woods, the joints can corrode and separate from the lower control arms. That's bad if you enjoy steering your CX-7. According to Mazda, owners of affected models may notice a rattle from the front suspension due to the loose ball joint in the lower control arm fitting. Mazda describes separation of the ball joint and control arm as a "worst case" scenario "after extended operation in such condition." Injuries/Deaths: It's unknown if the rusting issue has led to any crashes, injuries, or deaths. Autoblog has a call into Mazda for additional details and will update this post with any new information. There have been no reports of accidents, injuries, or fatalities related to this recall. The Fix: Owners should report to their local Mazda service center, where techs will replace the both front lower control arms. Any work done is free of charge. If you own one: Mazda will perform some automotive triage with this recall, focusing on CX-7s that have had the longest exposure to salt and are most likely to suffer control arm separation first. Owners of 2007s and 2008s come first, followed by 2009 through 2011 models. Mazda will also focus on vehicles registered in states where snow and road salt are most common – Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin, and Washington, D.C. If you live in a more temperate region or own a 2012 CX-7, Mazda will perform recall work as "parts are available." Owners can contact Mazda customer service at 1-800-222-5500 for additional info. Recall notices should hit the mail around October 10th. Related Video: Featured Gallery 2011 Mazda CX-7: Review View 21 Photos News Source: NHTSAImage Credit: Copyright 2016 AOL Recalls Mazda Crossover mazda cx-7

Mazda CX-5 getting mild refresh

Mazda has found both critical and commercial success with its CX-5 small crossover, and seems to be endeavoring to keep the momentum up with an upcoming refresh. As you can extrapolate from the obvious lack of the usual camouflage, the company isn't reinventing anything in the very near future of the CX-5, but it does seem as thought some tweaks are in the works.
Lighting elements fore and aft appear to have gone under the knife, with the front grille and rear fascia also seemingly to be slightly revised. The side mirrors now look slicker and slightly more upscale with their integrated turn signals, as well.
In all, expect a look that's a touch fresher, without being a radical departure from the existing visage.

Japanese students turning Mazda CX-5 into Dakar Rally-ready off-roader

Students at Japan's Nihon Automobile College (NATS) are transforming a first-generation Mazda CX-5 into a full-blown off-roader that looks ready to compete in the Dakar Rally. Named CX-Runner, the one-of-a-kind model will make its debut at the Tokyo Auto Salon opening its doors in January 2020. The Tokyo Auto Salon is the Japanese equivalent of the annual SEMA show, so anything goes under the bright lights. NATS students began the CX-Runner project with a used 2012 CX-5 and seemingly set out to leave as few original parts as possible. While the project isn't finished yet, a sketch released by the school suggests the crossover will receive wheel arch extensions, an external roll cage, a beefier suspension, and a shorter front bumper that increases the approach angle.  Photos published on the school's official Facebook page show the project is moving along nicely. The body extensions are made with a composite material that looks like Kevlar, and fitting the rear wheel arches required sealing the back doors, which is fine; the CX-Runner will be a two-seater. We don't know if students are planning to make changes to the CX-5's powertrain yet, but a thick skid plate will protect whatever is under the hood from expensive impacts with obstacles encountered off-road. nats-mazda-cx-runner-project-1 View 3 Photos The Tokyo Auto Salon will open its doors on January 10, so the students have time to finish the custom-made body kit, install the suspension, paint the CX-Runner, and fit the roll cage. They're not just doing this for fun, though. NATS began offering a customizing class in 1998, and building a tuner car is one of the requirements aspiring builders need to fulfill in order to graduate. With that in mind, it's no surprise that NATS will again have a big presence during the 2020 edition of the Tokyo Auto Salon. In addition to the CX-5 off-roader, its students are building six custom cars including a Nissan 370Z roadster wearing front and rear fascias sourced from a GT-R, a Toyota 2000GT-inspired convertible based on the Suzuki Cappuccino kei car from the 1990s, and a four-door, five-seater Toyota 86 built on Camry bones but powered by the coupe's flat-four engine. Relate Video: