2014 Mazda Cx-5 Touring on 2040-cars

Auto blog

Mazda goes on engineer hiring binge as recovery picks up speed

Japan's larger automakers - companies like Toyota, Honda and Nissan - have tremendous engineering talent at their disposal. That's largely because, selling as many cars as they do, they've got more revenues to tap into. Logic might dictate, then, that smaller automakers like Mazda, which no longer has the deep pockets afforded to it by its former partnership with Ford, might have less of a budget and workforce for engineering. But Mazda has been raking in record profits, and it plans on cashing those revenues in by hiring a substantial new pool of engineers.
According to Automotive News, Mazda is preparing to hire as many as 185 new engineers over the next two years - almost four times as many as the 50 engineers it previously targeted. Many of those engineers will be put to work developing the second-generation, Skyactiv 2 technologies that are on the drawing board while the first round of Skyactiv features are still being rolled out.
The boost in recruitment is enabled by a positive fiscal year that ended last March, marking the first profits Mazda had logged in four years. Sources anticipate that the fiscal year culminating at the end of this month will mark the company's most profitable yet, netting over a billion dollars to eclipse the fiscal year that ended in 2008 when it recorded $872.5 million in profits.

Confirmed: Mazda Miata gets more power, higher redline, telescoping wheel

Our friend over at Road & Track, Bozi Tatarevic, has a keen nose for stuff just like today's Miata news, and he spotted an article by the Japanese car magazine Car Watch that details Mazda's upcoming updates. Car Watch actually got to drive the car, too. There's a lot to go through, but the highlight has to be confirmation of what we told you earlier this year about a significant power bump: The Miata will indeed get an increase of 26 horsepower, from 155 to 181. But the power's not the whole story. Mazda has increased the redline from 6,800 RPM to 7,500. It's not clear at this point where torque and power peaks are in the rev range, or how these changes affect low-speed drivability, but more revs are almost always a good thing and aren't likely to detract from the roadster's fundamental goodness. Car Watch reports that lighter pistons and connecting rods are fitted to help reduce rotational mass in the 2.0-liter inline-four. Some valvetrain changes were needed to support the higher redline, mainly stiffer valvesprings to prevent valve float. Mazda also changed the shape of the valves and optimized the intake ports to breathe better at higher RPM. The inner diameter of the exhaust ports were increased to flow better through a new muffler better tuned to the engine's new operating range. This confirms and gives a little more detail to what we reported earlier based on a leaked document from Mazda Canada. Car Watch also confirms that the revised Miata will get a low-inertia dual-mass flywheel, which should help absorb some vibration, noise and harshness from the higher-revving engine without losing too much of the directness that a single-mass flywheel provides. Mazda usually gets stuff like this right, so while we won't know until we get a chance to drive it whether the DMF feels "right," we're not too worried about it. There's also a telescopic steering wheel, a first in any Miata, which has a range of about 1.1 inches. That doesn't sound like much, but it should help folks with longer legs reach the wheel without having to crank the seat forward. Interestingly, Car Watch reports that the telescoping wheel was opposed by some in the company seeking to save every fraction of an ounce of weight, and to get it through, the company apparently had to change some of the material in the upper steering column from steel to aluminum to satisfy the weight-conscious. Little details like these are fantastic.

Mazda6 diesel may finally launch this year according to CARB certification

For close to a decade, Mazda said it would bring its latest generation of diesel engine, Skyactiv-D, to the United States. And for most of that time, it said that engine would appear in the Mazda6. Last year Mazda finally brought us the engine in the CX-5, and it looks like this year, the 6 will finally get it, too. This seems to be the case based on a CARB certification posted on January 31 specifically for the midsize family sedan. The CX-5, in both front-wheel- and all-wheel-drive variants, is listed in a different certification, so it's not a case of a blanket certification for every vehicle the engine could appear in this year. As expected, the document lists the 6 as having a 2.2-liter turbocharged engine with a six-speed automatic, though it doesn't say whether the model is front-wheel-drive or all-wheel. Either is certainly possible, since all-wheel drive, in particular with the diesel, is available in overseas Mazda6s. Like in the CX-5, the engine will probably make 168 horsepower and 290 pound-feet of torque. While this certification tells us the diesel 6 will probably launch this year as a 2021 model, we're left to estimate the reveal date. Midway through the year, or possibly at the start of the next auto show cycle would seem likely, which would coincide with a model year update. Mazda has stated it will only be offered on the top-tier Signature trim, which starts at $36,345 with the standard turbocharged gasoline 4-cylinder. Looking at the price difference between a turbocharged Mazda CX-5 Signature with all-wheel-drive and the diesel CX-5, the price difference is about $4,000, so it would seem reasonable to expect the Mazda6 diesel to ring in at about $40,000. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.