3.7l Cd Keyless Start Front Wheel Drive Active Suspension Power Steering Abs on 2040-cars

Auto blog

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"

Ford Q3 pretax profits drop to $1.18B

Following positive third quarter financial results recently from General Motors, rival Ford took a tumble in Q3. The automaker posted pre-tax profits of $1.18 billion, compared to about $2.59 billion in Q3 2013, a drop of around 54 percent. Net income also suffered with $835 million made in the quarter, versus $1.272 billion last year, a decline of about 34 percent. The Blue Oval blamed the gloomy figures on three reasons in its release: "lower volume, higher warranty costs and adverse balance sheet exchange effects."
There were problems of one kind or another in practically every region. North America experienced higher warranty costs than expected, partially due to recalls. The sales volume for the quarter was 665,000 units, versus 725,000 in Q3 2013, and pre-tax results amounted to $1.41 billion versus $2.296 billion last year.
South America and Europe both posted worse pre-tax results than last year. On the bright side, European volume was up slightly to 321,000 vehicles, from 303,000 in Q3 2013. The Middle East and Africa also lost $15 million, but that was an improvement compared to the $25 million loss previously experienced in this region.

Ford recalls 90,736 vehicles due to engine valve issue

Ford will recall 90,736 vehicles as engine intake valves in the vehicles may break while driving, the National Highway Traffic Safety Administration (NHTSA) said on Saturday. The recall impacts certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine, the NHTSA said. According to documents posted by NHTSA and sourced from the automaker, "The engine intake valves may break while driving, which can result in engine failure and a loss of drive power." Following an investigation that started in January, 2022, Ford found 22 instances where "the engine intake valves fractured and fell into the combustion chamber of the engine causing catastrophic engine damage." The automaker's analysis continues: "Ford identified that the potential root cause of the failures was engine intake valve failure due to valves that exceeded the designed specification for hardness, were brittle, and more likely to fracture. Ford determined that this was due to the supplier’s grinding processes and the sensitivity of the intake valve material to grinding processes that were not within control specifications. The intake valve material was changed for vehicles produced after October 31, 2021." Fixing the problem will require replacement of the entire engine. "Dealers will inspect each vehicle to determine its cumulative number of engine cycles. For vehicles that do not meet the engine cycle threshold, dealers will accumulate high revolutions per minute (rpm) engine cycles per a service procedure. Engines will be replaced on vehicles that do not pass the engine cycle accumulation," Ford says.