2014 Jeep Wrangler on 2040-cars

Auto blog

EPA suspected Fiat Chrysler of using 'defeat device' in 2015

U.S. regulators told Fiat Chrysler Automobiles in November 2015 that they suspected some of the automaker's vehicles were equipped with secret software allowing them to violate emission control standards, according to emails disclosed on Friday. The U.S. Environmental Protection Agency and California Air Resources Board accused Fiat Chrysler in January of using the software, known as a "defeat device," to illegally allow excess diesel emissions in 104,000 Jeep Grand Cherokees and Dodge Ram 1500 trucks built between 2014 and 2016. Byron Bunker, director of the EPA's Transportation and Air Quality compliance division, said in a January 2016 email to Fiat Chrysler, obtained by Reuters under the Freedom of Information Act, that he was "very concerned about the unacceptably slow pace" of the automaker's efforts to explain high nitrogen oxide emissions from some of its vehicles. Nitrogen oxide is linked to smog formation and respiratory problems. Bunker's email said the EPA had told Fiat Chrysler officials at a November 2015 meeting that at least one auxiliary emissions control device on the car maker's vehicles appeared to violate the agency's regulations. Mike Dahl, head of vehicle safety and regulatory compliance for Fiat Chrysler's U.S. unit, responded in a separate email that the company was working diligently and understood the EPA's concerns. He added that if the EPA identified Fiat Chrysler vehicles as containing defeat devices it would result in "potentially significant regulatory and commercial consequences." The documents redacted the vehicles named, but two officials briefed on the matter said they referred to diesel models. The EPA's November 2015 meeting with Fiat Chrysler came two months after Volkswagen AG, mired in a major tailpipe emissions scandal, admitted to installing secret defeat device software in hundreds of thousands of U.S. diesel cars to make them appear cleaner than they were on the road.

First Jeepster prototype spotted with final, boxy form

The long-awaited baby Jeep is getting closer to production, as evidenced by these spy photos. Previously, the only images of the so-called Jeepster saw it wearing a Fiat 500L body (see below), while this new batch of photos show hefty amounts of camouflage. How is that better? Well, it's very likely there's a production body hiding under all that cladding.
While picking out styling details is virtually impossible thanks to all the camo, as our spies point out, this gives us a very sound idea of the Jeepster's final size. It's small, although we'd argue that it's only slightly smaller than the current Jeep Patriot, based on the images of the newest Jeep sitting in front of an Alfa Romeo Giulietta.
As we reported previously, this little bambino will be built on a Fiat platform, but the styling should be uniquely Jeep - likely to include a somewhat vertical seven-slat grille and round headlights. We can expect to see a production Jeepster, if that ends up being the actual name (Latitude has been rumored, although as that's traditionally a trim level, we imagine there'd be some confusion), when it debuts at the 2014 Geneva Motor Show.

Jeep readying 2018 and 2019 Wrangler recall for bad frame welds

According to documents posted to the JL Wrangler Forums, Jeep is readying a recall for an unknown number of 2018 and 2019 model-year Wrangler SUVs. The issue revolves around the track bar mount, which on some vehicles is shearing off where it is welded to the frame. Since some affected vehicles may be unsold on dealer lots, the automaker has issued a corresponding stop sale. A Jeep spokesperson confirmed to CNET that there have been no reported accidents related to the issue, and Jalopnik reports that Jeep will inspect roughly 18,000 vehicles for the defect, though it believes only around 720 will be affected. As of the time this story was published, the National Highway Traffic Safety Administration had not yet posted this recall to its website. There have been a total of five recalls for the 2018 Jeep Wrangler, including one for a steering shaft that could separate due to improper welding. One 2018 Jeep Wrangler owner in North Carolina posted a video to YouTube, seen above, showing track bar mounts that have completely sheared away from the vehicle's frame. These broken welds may cause severe steering degradation and "can cause a vehicle crash without prior warning," according to a dealer notice that was posted to the JL Wrangler Forum. That owner has said Jeep is replacing his Wrangler, but it's not clear if other vehicles are being replaced or repaired. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.