2007 Jeep Wrangler on 2040-cars

Auto blog

Stellantis wants to trim 3,500 hourly U.S. jobs, UAW says

WASHINGTON — Chrysler-parent Stellantis NV wants to cut approximately 3,500 hourly U.S. jobs and is offering voluntary exit packages, according to a United Auto Workers union letter made public Tuesday. The automaker is looking to reduce its hourly workforce offering incentive packages that include $50,000 payments for workers hired before 2007, UAW Local 1264 said in a letter dated Monday posted on its Facebook page. Stellantis spokeswoman Jodi Tinson declined to comment. A person briefed on the matter said the figure might be lower than the figure cited in the UAW letter. In late February, Stellantis indefinitely halted operations at an assembly plant in Illinois, citing rising costs of electric vehicle production. The action impacted about 1,350 workers at the Belvidere, Illinois, plant that built the Jeep Cherokee SUV and resulted in indefinite layoffs. The automaker has warned it may not resume operations as it considers other options. The UAW letter said openings created by workers leaving would be filled by workers on indefinite layoff. Stellantis said in February that about 40,000 U.S. hourly workers were eligible for profit sharing. Last week, UAW President Shawn Fain said Stellantis' decision to idle the Illinois plant was "a flat-out violation" of the union's contract with the UAW and is unacceptable. The UAW will enter talks with the Detroit Three before labor contracts expire in mid-September. Earlier this month, General Motors said about 5,000 salaried workers accepted buyouts to leave the automaker. GM CEO Mary Barra said February job cuts of a few hundred jobs and the 5,000 buyouts "provided approximately $1 billion towards" a $2 billion cost cutting target. Ford Motor Co recently announced significant job cuts in Spain, Germany and other parts of Europe and in August said it would cut a total of 3,000 salaried and contract jobs, mostly in North America and India. Hirings/Firings/Layoffs UAW/Unions Chrysler Dodge Fiat Jeep Maserati RAM Stellantis

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Jeep Wrangler pickup's rear suspension is inspired by Ram

Although we've learned about all there is to know about the new Jeep Wrangler, there is still more to discover about its upcoming truck sibling, such as the rear suspension. We knew it would be coil-sprung, but these new spy shots also indicate that the suspension is more similar to what's under a Ram 1500 than the Wrangler SUV. In the gallery above, the first two images compare the rear suspension of a new-generation 2018 Wrangler (left) and the Wrangler pickup (right). Immediately obvious is that the shocks on the Wrangler SUV are mounted at the back of the axle, while the truck's shocks are mounted at the front. It's also possible to see that the anti-roll bar on the SUV is mounted quite high up, while the truck's bar sits much lower, near the base of the rear axle. The third image shows a Ram 1500 on the left and the Wrangler pickup on the right. Here we can see that the Ram shares the same sort of low-mounted anti-roll bars and forward-mounted shocks, along with a Panhard rod. The two aren't quite the same, though. For one thing, the Wrangler pickup's rear axle looks more like the Wrangler SUV's than the one on the Ram. It's possible that these suspension changes were made in an effort to boost the Wrangler truck's payload capabilities. It's also possible that there are some handling quirks to the long truck body style for which a Ram-style suspension was better suited. We'll look forward to learning more about the differences when the truck is revealed, likely in early 2019. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.