2011 Jeep Grand Cherokee Overland 4x4 4dr Suv on 2040-cars

Auto blog

Chrysler resolves recall issue with NHTSA, will inspect, upgrade affected Jeeps

Chrysler made big news earlier in the month by refusing a recall request from the National Highway Traffic Safety Administration for the 1993-2004 Jeep Grand Cherokee and 2002-2007 Jeep Liberty. Last week, NHTSA boss David Strickland countered by defending his agency's request for the recall of 2.7 million Jeep SUVs. Today marked the deadline for Chrysler to formally respond to NHTSA, and it seems that both parties have met in the middle with Chrysler inspecting and upgrading some of the affected vehicles without using the word "recall," which would constitute the admission of a defect; instead, Chrysler said that it is conducting a "voluntary campaign."
At issue on these vehicles is the positioning of the fuel tank behind the rear axle that could get damaged during a rear-end collision. NHTSA has stated that at least 51 people have been killed in rear-end collisions involving these Jeeps after the vehicles caught fire, to which Chrysler countered by pointing out that both models "met and exceeded" the requirements for fuel-system integrity.
As a compromise on the situation, Chrysler says that it will inspect all pre-2004 Grand Cherokees and pre-2007 Liberty models and, "if necessary, provide an upgrade to the rear structure of the vehicle." According to Automotive News, this upgrade will consist of adding a trailer hitch that will presumably better protect the rear-mounted gas tank. Vehicles already equipped with a factory or Mopar hitch will not be modified. Chrysler's official statement on the matter is posted below, but no additional information has been released, such as when the campaign will begin and how many vehicles could be affected.

What's really going on with the 2014 Jeep Cherokee's transmission issues?

On September 23, Automotive News reported that Chrysler had idled the second shift workers it hired just five weeks prior at its Toledo Assembly Complex to build the 2014 Jeep Cherokee. At the time, Chrysler said it had "built the critical number of vehicles we need to stock dealerships once containment is released" and did not want "to put additional strain on our logistics partners ... upon release." That reasoning was not only unusual, it didn't seem to make sense.
It appears the center of the nine-speed issue is software, not hardware.
That same day, the Detroit News ran a piece claiming workers at the Toledo factory said the halt was due to issues with the Cherokee's transmission. It put the number of already-built Cherokees needing fixes at 1,000 and said that some of the workers not laid off had been instructed "to take the Jeep on long test-drives." That made more sense. Three days later, on September 26, Automotive News reported that the 500 workers laid off had been reinstated, with engineers "speeding repairs on the SUV's powertrain software." The AN piece didn't put a number on how many units are being fixed, but it did say that 12,000 have been built and are awaiting delivery to dealers. The best it could say about when dealers will get them, however, is that "progress on a fix is being made. It's unclear when shipments to dealers will start."

2018 Jeep Wrangler will have an aluminum hood and doors, leaked memo says

Earlier this year, FCA CEO Sergio Marchionne revealed that 2018 Jeep Wrangler would feature a heavy dose of aluminum, though he didn't specify how. Now, JL Wrangler Forums says the Wrangler will use the material for the hood and the doors, citing an internal bulletin from aluminum supplier Alcoa. According to the forum, the company says the next-gen Wrangler will utilize Aloca's C6A1 (an internal name) high form alloy. The SUV will also get 6022 and A951 from Alcoa that will be used on the SUV's front and rear doors, as well as for the hood. Alcoa's C6A1 is the company's new high form alloy, while its 6022 alloy sheet can be found on things like a car's hood, door, or closure panels. Alcoa's A951 is the company's pre-treatment aluminum sheet bonding technology that it uses on automobiles. "A team in the Farmington Hills (Michigan, USA) Aerospace and Automotive Products group is leading a new profitable growth opportunity with the 2018 Jeep Wrangler program. The next generation Jeep becomes the first to utilize our C6A1 high form alloy; we are currently the only supplier of this high form product. Alcoa will also supply 6022 and A951, including front and rear door inners, hood outer and inner." As Marchionne pointed out earlier this year, the 2018 Wrangler won't be made entirely out of aluminum. So Alcoa's contribution to the upcoming SUV's doors and hood could be the only components that use the lightweight metal – or Jeep could be using another aluminum supplier for other parts. Large changes lie ahead for the 2018 Wrangler, which include a pickup version, new engines, and aluminum. But we do know that the next Wrangler is that it will be built in Toledo, OH, as FCA announced plans to spend $1.05 billion to retool the Wrangler factory, while also adding another site in Illinois earlier this year. Related Video: