2011 Sport Used 2.4l I4 16v Automatic 2wd Suv on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Certain Chrysler owners eligible for buyback program

Certain car owners whose Chrysler vehicles contain dangerous defects will soon have a way to get rid of their lemons without losing money. As part of an agreement with federal regulators, Fiat Chrysler Automobiles has agreed to buy back more than 500,000 vehicles susceptible to veering out of control without warning at above market-value prices. The deal mainly covers certain models of RAM trucks, the Dodge Dakota pickup and Dodge Durango SUV. Further, owners of more than 1.5 million Jeep Liberty and Grand Cherokees at heightened risk for lethal fires are eligible to trade in their vehicles at above market value or, alternately, get a gift certificate if they prefer to have repairs made. Chrysler has "a heavy responsibility to make sure the products they make are safe for the traveling public," said Mark Rosekind, administrator of the National Highway Traffic Safety Administration. "... Here, we are sending an unambiguous signal to industry that if you skirt the laws or violate the law, or don't live up to the responsibility that consumers expect, we are going to penalize you." The buy-back and trade-in options for motorists come as part of an unprecedented penalty NHTSA slapped against Chrysler for violating federal motor-vehicle safety laws. Chrysler will pay a $105 million fine, the highest ever levied by the regulatory agency. In addition to the buy-backs, Chrysler also agreed to an independent monitor for three years. Investigators had outlined problems in the company's conduct in 23 recalls that affected more than 11 million defect vehicles. As part of a consent-order agreement, Chrysler acknowledged it did not notify vehicle owners of recalls in an effective manner and did not notify NHTSA of safety problems. Though those recalls affected millions of drivers, the buy-back and trade-in options are only for a small portion of the vehicles involved. Because Chrysler struggled to fix the problem and no repair was apparent, Rosekind said the buy-backs are reserved "for customers who didn't have a remedy." Buy-backs are for trucks and SUVs affected by three recalls that occurred in 2013 (recalls 13V-038, 13V-527 and 13V-529), that addressed a rear-axle pinion nut that could come loose and cause a loss of vehicle control. Those recalls covered 579,228 vehicles, including 2009-2012 Ram 1500, 2500, 3500, 4500 and 5500 trucks, 2009-2012 Dodge Dakotas, 2009 Chrysler Aspen and the 2009 Dodge Durango.

Best places to get your car maintained and repaired

In this era of rampant inflation and high interest rates, the challenges of acquiring a car or SUV have been well documented. And so it has never been more important to protect that expensive investment by maintaining it. In recent months, Autoblog has shared Consumer Reports' evaluation of the least and most expensive car brands to keep running, as well as tips to prolong a car’s useful life. Especially since the pandemic, a number of factors have impacted these costs: more complex vehicles, new materials and manufacturing methods, a shortage of qualified technicians and replacement parts. Since 2022, repairs costs have jumped each year by about 10 percent. This month, Consumer Reports is offering a useful primer on keeping your ride in great shape, suggesting what might be the best options for searching out a repair shop, depending, as CR says, “on your car and your situation.” Author Ben Preston identifies three basic types of repair facilities: dealership service departments, independently owned repair shops, and chain repair shops. Building up trust with a specific shop and feeling comfortable going there is important. Preston quotes John Ibbotson, chief mechanic at Consumer ReportsÂ’ Auto Test Center: "You might be able to save a few bucks by going to whichever shop offers the cheapest prices, but if you want consistent, reliable service, itÂ’s best to find a repair shop you trust and stick with it,” Ibbotson says. The story goes on to evaluate each type of service facility. HereÂ’s a breakdown of CRÂ’s findings: Dealerships These work well for owners of newer cars, especially for covered warranty work. But the disadvantage is the high labor rates common to dealer service. Satisfaction ratings for dealer service departments range from very good (Acura, Lexus, Mazda, and Volvo) to not-so-good (Jeep and Kia). Dealers are best for: Fixing infotainment system glitches: "If the screen in the center of your dash has a habit of freezing up, or the touchscreen-activated climate controls arenÂ’t working, the dealership is the most likely place to find someone with the know-how to fix problems that maybe only a factory-authorized technician can access," Ibbotson says. Safety system recalibration: "Anything from a crack in your windshield to a minor fender dent can upset the calibration of the sensors that make features like automatic emergency braking and adaptive cruise control work," says Ibbotson.