65k Miles Clean Carfax Leather Moonroof Coupe V6 Black on 2040-cars

Auto blog

Honda recalls 25k Fits over grab handle, airbag issue

Honda has issued another recall for the Fit. Only this time, it comes down to a very specific issue arising in a limited cross-section of production. The recall affects over 25,000 units in the United States alone. This problem results from the bracket affixing the rear grab handle, which was apparently manufactured incorrectly. As a result, the bracket may puncture the side curtain airbag as it deploys. That's bad news, so Honda is recalling the affected vehicles to have that bracket replaced. According to the manufacturer, the issue was discovered during its own internal testing procedures, and not because of any reported incidents. The problem only affects Fit hatchbacks from the 2015 and 2016 model years, manufactured between April 11, 2014, and July 2, 2015. Even within those confines, however, the recall is limited only to those in LX trim level and not equipped with a sunroof. That amounts to an estimated 25,367 units in the US - less than a third of the 84,000+ units American Honda sold in the same fifteen-month period. This is the third recall that has affected the Fit in as many months. Last month saw 143,000 units of the Fit and Civic recalled over a transmission issue. In September, the Japanese automaker called in another 18k Fits over a problem with their ignition coils. RECALL Subject : Improper Rear Grab Rail Bracket/FMVSS 214/226 Report Receipt Date: OCT 23, 2015 NHTSA Campaign Number: 15V697000 Component(s): AIR BAGS , STRUCTURE Potential Number of Units Affected: 25,367 Manufacturer: Honda (American Honda Motor Co.) SUMMARY: Honda (American Honda Motor Co.) is recalling certain model year 2015-2016 Fit LX-trim vehicles manufactured April 11, 2014, to July 02, 2015 and not equipped with a sunroof. In the affected vehicles, the rear grab handle brackets were not manufactured properly, and as a result, the brackets may puncture the side curtain air bags upon their deployment. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 214, "Side Impact Protection" and number 226, "Ejection Mitigation". CONSEQUENCE: If the side curtain air bags are punctured upon deployment, the outboard seat occupants may be at a higher risk of injury during a crash. REMEDY: Honda will notify owners, and dealers will replace the rear grab handle bracket, free of charge. The recall is expected to begin December 4, 2015. Owners may contact Honda customer service at 1-888-234-2138. Honda's number for this recall is JV8.

James Glickenhaus' SCG 003 undisguised in street and track form

For James Glickenhaus buying a factory-made supercar isn't good enough; he wants to develop his own. Following up on the Ferrari Enzo-based P4/5 and later the P4/5 Competition, Glickenhaus' latest project is appropriately called the 003, and he's finally displaying it in road trim. These first undisguised photos of the SCG 003S show off a supercar with a front end reminiscent of a Ferrari Enzo. However, the rear evokes the look of a modern endurance racer with a fin running along the spine. A wing at the back connects it all together, and the massive diffuser should keep things planted too. Development of the 003 has been going for over a year by Scuderia Cameron Glickenhaus, but the company has set quite a challenge for itself to get just right. Glickenhaus wants his latest project to be a true racecar for the street. That idea gets thrown around a lot, but it might be true in this case. In motorsports trim, the SCG 003C (pictured inset) packs a mid-mounted Honda Performance Development twin-turbocharged V6, but the engine sits in a detachable rear subframe. When the time comes for the road, the car converts to the SCG 003S and allegedly swaps in a twin-turbo W12. It makes the vehicle the best of both worlds – at least in theory. SCG reportedly plans to show the 003 at the Geneva Motor Show, so we should get a better look then. Glickenhaus also wants to take the car racing in the 24-hour events at the Nurburgring and Spa later this year.

Honda CR-Z carbon-fiber prototype

When Honda rolled out the CR-Z a few years ago, it hoped to bridge the gap between those who would save the planet and those who would rather burn all of its resources in a glorious cloud of tire smoke. But enthusiasts recalling the CRX of 1980s vintage balked, imploring Honda to ditch the heavy battery packs and electric motors in favor of a lighter-weight, more conventional powertrain. At this point it seems less likely that Honda would do so at one end of the market than Porsche would ditch the hybrid component of its 918 Spyder at the other. But that doesn't mean Honda isn't still cooking up ways to curb the CR-Z's weight. And it had just one such idea waiting for us when we visited its Japanese R&D center at Tochigi last week.
Nestled in between the JDM hatchbacks, powertrain test mules and new technology prototypes Honda rolled out for us sat the experimental CR-Z you see here. While it may look mostly like the hybrid sport-hatch you can pick up at your local dealer (albeit blacked out), nearly all of this prototype's bodywork has been completely replaced, as have its basic underpinnings, with carbon-fiber reinforced plastic. The exotic material is usually reserved for high-end exotics, but like BMW is democratizing its use in the new i3, so too is Honda researching ways to implement the use of carbon fiber on a mass scale. This one-of-a-kind CR-Z prototype stands, for the time being, as the embodiment of that effort.
Driving Notes