2015 Gmc Yukon Slt on 2040-cars

Auto blog

GM recalling 54k Cadillac SRX, HD pickup models

There are more recalls to report General Motors, but these latest actions pertain to newer examples of the Cadillac SRX, Chevrolet Silverado HD and GMC Sierra HD. With so much scrutiny on the company's recall strategy, GM is under increasing pressure to call in defective models more quickly, and it appears to be doing so here.
Here in the US, the automaker is recalling 50,571 Cadillac SRX crossovers from the 2013 model year fitted with the 3.6-liter V6 because the transmission control module programming can cause a three- or four-second lag in acceleration at low speeds. The explanation filed with the National Highway Traffic Safety Administration states, "if the following sequence occurs within two seconds: during an upshift from first to second gear (8-10 mph), the driver then brakes the vehicle to less than 5 mph, and then accelerates again," the delay can occur. According to Automotive News, the recall effects 56,400 vehicles worldwide, and the company is not aware of any crashes caused by the problem. The fix consists of a transmission control module (TCM) reflash.
In a separate recall, GM is repairing 51 Chevrolet Silverado HD and GMC Sierra HD pickups from the 2015 model year in the US. In vehicles with diesel engines and dual fuel tanks, the nuts that connect the fuel pipe to each side of the transfer pump between the tanks may be improperly torqued, which could cause a fuel leak. Obviously, this could be a fire hazard. The remedy is simply tightening the hardware. According to GM spokesperson Alan Adler, there have been no fires actually caused by the potential leak. "Only 21 of the trucks are in customer possession and they can be fixed anytime because there are no parts involved. The others are being fixed at dealerships," Adler said in an email to Autoblog.

NHTSA opens safety investigations into Toyota, GM and Honda crossovers

The National Highway Traffic Safety Administration is evidently keeping itself very busy these days, as the federal agency has just announced it is launching or renewing investigations into Toyota, Honda and General Motors crossovers.
2006-2008 model year Toyota RAV4 crossovers are under review for allegations of rear tie-rod rust which can result in failure. NHTSA also said it is probing some 35 complaints about 2005 Honda Pilot models with inappropriate activation of the vehicles' stability control system. The alleged malfunction can cause the vehicles to slow down or stop in bad unsafe situations. At the moment, NHTSA is reviewing a petition regarding the Pilot issue, a move that will determine whether it needs to open a full-blown investigation.
In addition, Saturn Outlook and GMC Acadia three-row crossovers built in 2007-2009 are getting looked at for "loss of low beam headlamp" function. One complainant said the wiring in his Outlook overheated and melted. NHTSA says it has received 415 complaints about the problem and a GM spokesman confirmed that the automaker already started a "Customer Satisfaction Program" in December to address the issue.

GM planning to put its fullsize pickups on a big diet, too

General Motors is just coming off a complete redesign of the Chevrolet Silverado and GMC Sierra for 2014, but in the US fullsize truck market, there is no rest for the weary. According to Reuters, plans are already unfurling for both trucks to drop pounds from their curb weight over the next few years, but this will unlikely be able to keep pace with the 700-pound diet targeted for the next-generation Ford F-150, a truck expected to debut late next year.
The biggest weight reduction for these trucks might not be available until the next full redesign, which will likely happen around 2019, but the article says that smaller updates could shave pounds in the meantime. Two examples given include an "aluminum-intensive" version of the Silverado that could shed 250 pounds and debut around the same time as the lighter-weight, aluminum-bodied 2015 Ford, and there is also talk of reducing weight for driveline components such as axles and driveshafts. These changes are all part of an attempt to meet strict new fuel economy standards coming in 2017, targets which will get even tougher in 2025.