2014 Gmc Yukon Denali on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

2019 GMC Sierra Denali First Drive Review | The more things change...

ST. JOHN'S, Newfoundland — Canadians love their GMCs. Both anecdotal and statistical evidence supports this. In certain areas of Canada, the Sierra outsells the Chevy Silverado. But in this area of Canada, Cape Spear, the morning fog and salt air are thick. This is the most eastern point in Canada, and the most eastern point of North America if you don't count Greenland. We woke up early and drove to the coast in the new 2019 GMC Sierra Denali, hoping to catch what was promised to be an absolutely spectacular sunrise. The sunrise was a no-go thanks to the fog, turning the sky into a grey mist that melted into the Atlantic. Still, if the world had an edge, this is what it would look like. Driving in an inspiring place like this invites introspection, and since we're in an GMC Sierra, why not examine the brand's place in the world? Recall that for years, a GMC showroom was just packed with slightly more expensive versions of other GM products. Badge engineering, if you will – a dirty word in our business, applied to such notable machines as the Cadillac Cimarron, Buick Terraza, Chevy Aveo and Saab 9-7X. Things, at least on the surface, seem to be changing. GMC says it's making a concerted effort to differentiate its product portfolio from the rest of GM, but the results have been mixed. The brands were supposed to have less product crossover. There's no GMC version of the Chevy Traverse and, initially, there was no Chevy equivalent of the GMC Acadia, though the new Blazer kills that advantage. The Equinox and Terrain are still basically the same vehicle, as are the new 2019 Silverado and 2019 Sierra. At least the two trucks look decidedly different. There's still a family resemblance, but most of the bodywork has been changed. Where the 2019 Silverado adopted some curves, the Sierra stuck with straight lines. Compare things like the headlights, wheel wells and doors. The Sierra still has a massive grille and — aside from the AT4 off-road trim — packs on as much chrome as a 1958 Cadillac, but that's what customers want these days. The Ford F-150 and Ram 1500 are no different in this regard, packing lots of chrome, hard edges, and frontal areas that would give passenger trains a run for their money. At first glance, you'd be hard pressed to tell the Sierra and Silverado's interiors apart from both each other and the outgoing models. It's basically the same design, though the Sierra makes do with some slightly nicer materials.

Detroit 3 to implement delayed unified towing standards for 2015

Car buyers have a responsibility to be well-informed consumers. That's not always a very simple task, but some guidelines are self-evident. If you live in a very snowy climate, you generally know a Ford Mustang or Chevrolet Camaro might not be as viable a vehicle choice as an all-wheel drive Explorer or Traverse, for example. If you want a fuel-efficient car, it's generally a good idea to know the difference between a diesel and a hybrid. But what if it's kind of tough to be an informed consumer? What if the information you need is more difficult to come by, or worse, based on different standards for each vehicle? Well, in that case, you might be a truck shopper. For years, customers of light-duty pickups have had to suffer through different ratings of towing capacities for each brand. For 2015 model year trucks, though, that will no longer be a problem. According to Automotive News, General Motors, Ford and Chrysler Group have announced that starting with next year's models, a common standard will be used to measure towing capacity. The Detroit Three will join Toyota, which adopted the Society of Automotive Engineers' so-called SAE J2807 standards way back in 2011. The standard was originally supposed to be in place for MY2013, but concerns that it would lower the overall stated capacity for trucks led Detroit automakers to pass. Ford originally passed, claiming it'd wait until its new F-150 was launched to adopt the new standards, leading GM and Ram to follow suit. Nissan, meanwhile, has said it will adopt the new standards as its vehicles are updated, meaning the company's next-generation Titan should adhere to the same tow ratings as its competitors. While the adoption of SAE J2807 will be helpful for light-duty customers, those interested in bigger trucks will still be left with differing standards. There is no sign of the new tow standards being adopted for the heavy-duty market.