We Finance!!! 2011 Gmc Sierra 1500 Denali Awd Nav Heated Leather Tow Texas Auto on 2040-cars

Auto blog

GM's redesigned full-size 2021 SUVs face delay over coronavirus

As General Motors works to conserve cash for the coronavirus pandemic, the automaker reportedly told suppliers that it is postponing development of several future vehicles. The situation may cause GM to delay the launch of the 2021 Cadillac Escalade, GMC Yukon, Chevrolet Tahoe and Chevrolet Suburban SUVs, which had been planned to roll out in April. The original launch plan for the redesigned full-size SUVs, which are some of the most profitable vehicles produced by GM, had called for production of the current models to end at its plant in Arlington, Texas, this week. After a retooling process, the redesigned SUVs were slated to begin production late in the month of April. In an email to suppliers viewed by Reuters and confirmed as authentic by GM, the automaker also said it was suspending development work on six future vehicle programs, including updates of the Chevrolet Equinox, GMC Terrain, Cadillac XT4, Bolt EV, Chevrolet Silverado and GMC Sierra. GM said preproduction work on those programs would be pushed back to calendar year 2021, with most of the updated vehicles scheduled to be launched as 2022 models. According to the Detroit News, work has also been paused on the Chevy Camaro and a future version of the Corvette that has yet to be unveiled and wasn't planned for production during the 2020 calendar year. Last week, the automaker told employees and suppliers it was delaying work on some future vehicles while pushing ahead with near-term models such as its redesigned full-size SUVs and the GMC Hummer EV, Cadillac Lyriq, Chevrolet Bolt EUV and Cruise Origin, as well as its new Ultium battery system. A GM spokesman who spoke with Reuters reiterated on Monday what the automaker had said last week — that the situation with its U.S. plants was "fluid" and that the automaker would "continue to evaluate" whether and when to reopen those plants on a week-by-week basis, with "employee safety" guiding that decision. GM said previously that it was closing most of its U.S. plants indefinitely. In its Monday email, GM asked suppliers to stop work on all pre-production tooling and pre-production parts manufacturing, but also not to dispose of any tooling or materials. GM told Reuters it had solicited volunteers from its workforce to finish the build-out of the current SUVs on a single shift in Arlington.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

2015 GMC Canyon Nightfall Edition rumbles in under the radar

Buyers enticed by the new 2015 GMC Canyon will want to take a look at the new Nightfall Edition. Unveiled here on the floor of the 2015 Detroit Auto Show, the Nightfall is based on the mid-level SLE trim level in four-door crew cab bodystyle, but upgrades with a stealthy appearance and bundled extras. It's decked out in Onyx Black paint, for starters, but also has a blacked-out grille and side steps, a spray-in bedliner and 18-inch wheels with darkened inserts, as well as a polished exhaust tip, remote start and automatic climate control fitted as standard. The only choice left up to the buyer of this murdered-out mid-size pickup is whether to get it in 2WD or 4WD. Either way, motivation is provided by the Canyon's 3.6-liter V6 with its 305 horsepower and 269 pound-feet of torque. Pricing has yet to be announced, but considering that the SLE on which it's based starts at $30,980 and that the SLT comes in at $34,345, we'd expect the Nightfall to be positioned in the low 30s, with another few grand for four-wheel drive. Featured Gallery 2015 GMC Canyon Nightfall: Detroit View 13 Photos Image Credit: Live photos copyright 2015 Drew Phillips / AOL Detroit Auto Show GMC Truck Detroit 2015 Detroit Auto Show gmc canyon