1999 Gmc Savana Tierra Conversion Van on 2040-cars

Auto blog

GM expanding Lansing Lambda CUV plant

Considering that crossovers are a rapidly growing portion of the US auto market, it's not surprising to hear that General Motors is preparing to build even more of them. The company is investing $63 million to expand its Lansing Delta Township Assembly plant that builds Lambda platform CUVs like the Chevrolet Traverse, GMC Acadia and Buick Enclave.
According to GM, the expansion will add roughly 263,000 extra square feet of space to the plant. Of that, 181,000 square feet will be for an updated body shop with cutting-edge robots. There will also be 54,000 square feet of additional room in the paint shop and 28,000 square feet of more area for general assembly.
GM isn't saying as much, but there is the possibility that this extra space could allow for additional models produced at the factory. Cadillac reportedly dropped plans to build a three-row SUV on the Lambda platform earlier this year, however, dealers for the luxury brand were recently pitched the possibility of adding large and small CUVs, an ATS convertible or a sedan below the ATS.

The Hummer EV Edition 1 is sold out and it'll be years before other trims arrive

When the 2022 GMC Hummer EV was revealed, GMC noted that there would be lower trims available. The company has since provided a few more details on those lower trims, which is helpful to know now that the only trim on sale next year, the Edition 1, was sold out in a scant 10 minutes. However, it's going to be a long time before they're all available.  The entry-level GMC Hummer EV is the EV2. This is the model that will start at $79,995, and unlike the Edition 1, it gets just two motors, one for each end of the truck, each with electronically locking differentials. Output is down to 625 horsepower and a torque rating of 7,400 pound-feet. Note that this and all other reported torque numbers are after the torque multiplication by the single-speed transmissions, hence the extremely high numbers. The company hasn't given torque numbers at the motors, which would be more comparable to other electric cars. Range is also reduced to 250 miles, probably due to a smaller battery pack. Fast charging is also restricted to 400-volt charging, so it won't be as fast as the higher trim models. The removable roof panels, retractable rear window, MultiPro tailgate, Super Cruise and 35-inch tires are standard. This model only gets fixed steel suspension and two-wheel steering. The EV2 will be the last of the trim levels to go on sale, with a target of spring 2024. Yes, as in 3.5 years from now.  The next level is the EV2X, which will be available a year earlier in the spring of 2023. It gets the same powertrain as the EV2, but adds 800-volt fast charging and a 300-mile range. It also gets the adaptive air suspension and four-wheel steering, plus the associated party tricks of Crab Mode and Extract Mode. This model costs $89,995. The earliest Hummer EV that isn't an Edition 1 and therefore not yet sold out will be the EV3X, the entry-level three-motor model. It goes on sale in the fall of 2022 at a price of $99,995. It's not quite as potent as the Edition 1, though, with an output of 800 horsepower and 9,500 pound-feet of torque. It also lacks the "Watts to Freedom (WTF)" launch control feature. But it does get torque-vectoring with the dual rear motors, which can also lock their speeds to be equal like with the mechanical locking differential at the front. The EV3X's range is 300 miles like the EV2X.  As for the Edition 1, it started $112,595 before it was sold out. Customers are to expect them in fall 2021.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.