Jimmy 4x4 1985 on 2040-cars

Auto blog

UAW rejects GM contract proposal but makes a counter offer

The United Auto Workers union said a new comprehensive offer made by General Motors Co late Monday to end a two-week-old strike was not acceptable and said it had made a new counterproposal. UAW vice president Terry Dittes said in a letter to members "there are many important issues that remain unresolved." The union is awaiting GM's next proposal. He said GM's offer came up short on many issues.  Dittes said GM made a "comprehensive proposal" at 9:40 p.m. Monday. "This proposal that the company provided to us on day 15 of the strike did not satisfy your contract demands or needs. There were many areas that came up short like health care, wages, temporary employees, skilled trades and job security to name a few." Dittes is the union's vice president for GM relations and the UAW's lead negotiator in these contract talks. "We have responded today with a counterproposal and are awaiting GM's next proposal to the union," he wrote. "Regardless of what is publicized in print or social media, etc., there are still many important issues that remain unresolved." The strike, in its third week, has cost GM more than $1 billion, according to J.P. Morgan analyst Ryan Brickman. He said the cost per day in potential profit is $82 million. However, another analysis, by East Lansing-based consultant Anderson Economic Group, put the losses at $25 million a day. And the effects of the strike are expanding. GM said Tuesday the strike has created a parts shortage that forced the automaker to halt production at its pickup and transmission plants in Silao, Mexico, temporarily laying off 6,000 workers. Silao is where GM builds its highly profitable four-door crew cab Chevy Silverado and GMC Sierra pickups. The strike has also forced GM to idle some Canadian workers, and many suppliers have been forced to halt operations. About 48,000 UAW members went on strike on Sept. 16 seeking higher pay, greater job security, a bigger share of the leading U.S. automaker’s profit and protection of their healthcare. 

GMC Syclone spools up a storm on Jay Leno's Garage

A storm was brewing on American roads in the early 1990s. That's when Detroit's automakers were producing some of the hottest performance trucks ever devised – models like the Ford Lightning, GMC Typhoon, and its flyweight pickup sibling, the GMC Syclone. Jay Leno just happens to have one of the latter in his garage, and took it out to showcase in this latest video segment. The Syclone was an exercise in absurdity, and could not only trounce any other pickup on the road, it could outrun anything else GM made and just about anything else on the road – beating Ferraris and Porsches off the line. In a pickup, for crying out loud. The kicker is that its engine wasn't such a monster, either: under the hood sat a 4.3-liter turbocharged V6 pumping out what would seem by today's standards to be an adequate 280 horsepower and 350 pound-feet of torque. Even the smaller of the EcoBoost V6s available in today's Ford F-150 produces more than that. But in a lightweight, compact pickup, those figures were enough to propel the Syclone to 60 in 4.3 seconds and run the quarter-mile in 13.6 seconds. Long before the dune-jumping Ford F-150 SVT Raptor or even the Viper-powered Dodge Ram SRT-10, GM made fewer than 3,000 Syclones based on the compact Sonoma (sister to the Chevy S-10) and another 4,700 of the Typhoon, which was mechanically similar but more practical (albeit heavier) wagon bodywork from the Jimmy. But as Jay aptly points out, the Syclone was the one you wanted. Scope it out in the ten-minute video clip above.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck