2004 Gmc Envoy Sle Sport Utility 4-door 4.2l on 2040-cars

Auto blog

GMC Hummer EV will weigh 9,046 pounds

In the 2000s, Hummer's unique breed of off-roaders summoned a dark cloud of disapproval from environmentalists because they were gas-guzzling SUVs with mammoth dimensions. GMC's born-again Hummer EV will escape the gas guzzler label by running solely on electricity, but it will be even bigger and much heavier than its predecessors. Enthusiast site GM-Trucks reported the Hummer EV will tip the scale at 9,046 pounds (4,103 kilos if you're outside of the United States) in its quickest configuration, and a GMC spokesperson told Autoblog that figure is accurate. For context, the H1 Alpha released for 2006 (and often considered the ultimate Hummer) weighed 8,113 pounds, the H2 checked in at 6,614 pounds with the 6.2-liter V8, and the H3 was comparatively light at 4,600 pounds. When it lands, the Hummer EV will be one of the heaviest new cars sold in the United States. Part of its plumpness can be attributed to its colossal dimensions; it measures 216.8 inches long, 86.7 inches wide, and 81.1 inches tall. In comparison, the H1 stretched 185 inches long, 87 inches wide, and about 78 inches tall. The electric powertrain also played a major role in slinging the Hummer's weight into dually pickup territory. Batteries are heavy, and the Hummer EV's Ultium pack reportedly has a capacity of over 200 kilowatt hours. It has three electric motors, too. Note the 9,046-pound figure applies only to the sold-out Launch Edition model, which will offer 1,000 horsepower, the aforementioned 200-kilowatt battery, and the supercar-like ability to hit 60 mph from a stop in three seconds. GMC will launch cheaper, slower, and presumably considerably lighter variants of the truck in the early 2020s. Although SUVs are often heavier than comparable trucks due to the additional sheet metal, the people-hauling Hummer should weigh less than the cargo-carrying variant. As we reported in April 2021, its output will be limited to 830 horsepower because it's 20 inches shorter than the truck, and the bigger battery pack doesn't fit in this footprint.

Barrett-Jackson rundown: 2024 GMC Hummer EV, Colin Powell's Corvette and more

The echoes of the last hammer fall at Barrett-Jackson's Scottsdale Auction have disappeared into the Arizona night, as have the record crowds and the traffic jams. During the Super Saturday charity auctions, three main attractions drove onto the dais for bidding: Late U.S. Chairman of the Joint Chiefs of Staff and Secretary of State General Colin Powell’s 2015 Chevrolet Corvette Stingray, the hammer price benefitting AmericaÂ’s Promise Alliance, the nonprofit Powell founded to support kids; The first production 2024 GMC Hummer EV SUV Edition 1 with VIN 001, proceeds going to Tread Lightly!, which educates people on how to enjoy the outdoors in a motorized vehicle and simultaneously protect the outdoors; And the first production 2024 Ford Mustang GT Fastback VIN 001, its hammer price benefiting the Juvenile Diabetes Research Foundation. Before the Saturday showcase, charity auctions on Friday took Barrett-Jackson past a huge milestone. When an 800-horsepower 2021 Shelby Super Snake Count's Kustoms Edition hammered for $350,000 to support the veteran's charity Camp Freedom, the auction house officially surpassed the $150 million mark for charity auction proceeds. Piling on before the clock struck midnight, a 2023 Ford F-150 Lightning 4x4 Super Crew sold for $275,000, those funds donated to Fighter Country Foundation. Then came Saturday. Powell's Gunmetal Gray on black Stingray was said to be a daily driver, but with just 15,600 miles on the odometer, Powell — who died in 2021 — apparently had a very short commute. Equipped with an eight-speed automatic transmission and chrome wheels, it sold for $200,000. The first production 2024 GMC Hummer EV SUV Edition 1 ran the bidding up to $500,000. That's quite a ways down on the $2,500,000 that the bedded 2022 GMC Hummer EV Edition 1 garnered at the charity auction in 2021, and not a bad price all things considered. The owner gets the first one off the line instead of getting lost in the 90,000-order backlog, and the markup goes to a good cause instead of a flipper and eBay fees. The first production 2024 Mustang GT Fastback brought in both less and more than the Hummer EV. The Ford's hammer price came to $490,000. However, two additional philanthropic donations for this lot in the amounts of $50,000 and $25,000 took the final price to $565,000. The big movers on the day were outside the charity sphere, four cars breaking the million-dollar mark.

2019 GMC Sierra Denali MultiPro tailgate and CarbonPro bed explained

When the 2019 Chevy Silverado debuted at the Detroit Auto Show in January, GM's Mark Reuss promised that the new 2019 GMC Sierra would have some significantly different styling and features than its corporate sibling. Previously, the Sierra has been little more than a Silverado with new front and rear fascias and some extra chrome inside and out. Well, Reuss was right. In addition to new sheetmetal, the Sierra exclusively gets the slick MultiPro tailgate and CarbonPro carbon-fiber bed box The tailgate really is trick. At the debut, GMC had multiple demonstrations, with engineers walking us through all six different configurations. Like all Sierra tailgates, the MultiPro version uses an aluminum skin to reduce weight. It's easy to tell which tailgate is which, as the MultiPro has a distinct cutout in the middle where it can fold down or extend. It can be used to extend the bed, drop to allow easier access, provide a sort of workbench, or be used as a step to help get into the bed. Yes, there's even a handle. Ford who? The step itself can support up to 375 pounds, 75 pounds more than Ford's similar tailgate step. This tailgate really is unique to the Sierra and is standard on SLT and Denali models. That said, the power-operated tailgate from the Silverado won't be coming to the GMC. Chevy gets its own exclusive, too. The Sierra's other big exclusive is the carbon-fiber reinforced plastic bed box. CFRP replaces steel inside the bed though not on the fenders. The bed uses four pieces; one for the bottom, one in the back and two along the sides. This isn't a CFRP. There is no steel hiding underneath these panels. Just take a peek underneath. The bed is a composite that uses 1-inch carbon-fiber threads, not a weave. Sheets of CFRP are molded and quenched — a process where the plastic coagulates and solidifies, locking in the carbon fiber — in just 60 seconds. That allows GMC's supplier to crank out these much more quickly. The finish looks like black fiberglass, though an engineer said that this wasn't the final production version. The final model will have different textures in order to improve grip and keep things from sliding around. GMC is touting the material's dent and corrosion resistance, though it remains to be seen how well it holds up to cracking. A video at the reveal showed people going after it with hammers and cinder blocks, but in-person demonstrations weren't available.