08' Gmc Denali Yukon Xl 4x4*fully Loaded*super Sharp* Escalade-suburban-tahoe on 2040-cars

Auto blog

2015 GMC Canyon gets the party started [w/video]

The 2014 Detroit Auto Show press days officially kick off tomorrow, but the night before all the madness commences, General Motors drove its new 2015 GMC Canyon pickup truck out for all to see. To refresh your memory, the Canyon is GMC's new midsize pickup - essentially a re-skinned version of the Chevrolet Colorado that debuted at the LA Auto Show in November.
Many of us at Autoblog prefer the look of the larger GMC Sierra to that of its Chevy Silverado kin, and we're having similar feelings about the new Canyon, especially after seeing it in person. It's sort of a pint-sized version of the Sierra, and it looks great. Clean lines are found throughout, and the Canyon's styling is decidedly premium.
At launch, the Canyon will be offered with the same engines as the Colorado - a 2.5-liter inline four-cylinder engine with 193 horsepower and 184 pound-feet of torque on the base end, and a larger 3.6-liter V6 with 302 hp and 270 lb-ft as an option. The Colorado's 2.8-liter diesel inline four-cylinder will be available after launch. Both two- and four-wheel drive configurations will be available, depending on the model.

GMC Sierra Denali CarbonPro bed is finally, almost here

GMC revealed the Sierra 1500 with the optional CarbonPro bed on March 1, 2018. The bed wasn't available at launch, though. You can't buy it now, either, but it will hit dealerships with limited availability after production starts in early June, exclusively for the Denali 1500 and AT4 1500 trims. The carbon floor and sides replace the steel panels in a normal bed, providing "strength, durability, and scratch resistance" and a potential 59-pound weight saving, depending on the truck's configuration. To make sure the bed had a chance, development engineers replicated "extreme use scenarios" like dropping 1,800-pound gravel loads, 450-pound steel drums, and cinder blocks from various heights. They put a 250-pound man on a snowmobile with studded tracks, had him drive into the bed and then go wide-open throttle. We're told the result was "minimal scratching." On top of the extreme weather testing any vehicle goes through, the team also put a generator in the bed and aim the exhaust into a corner to ensure vibration and direct heat wouldn't deform the carbon fiber. Because of the finer shaping area-specific strength possible with carbon fiber, the bed provides one cubic foot of additional payload space by having its sidewalls pushed further out. The CarbonPro bed doesn't need a bedliner, and is grained at the top for better traction but smooth on the bottom for easier hosing down and dirt removal. Tie-downs at the front of the bed work with molded indentations to hold motorcycle tires, and slots in the sidewalls hold two-by-sixes. The truck maker says the carbon-lined payload area confers "best-in-class dent, scratch and corrosion resistance," but we suppose the nation's pickup truck army will prove that or not. The trucks likely won't have the hardest life at the start, since the Sierra Denali costs $56,790 before even a basic option like four-wheel drive. The real test probably won't come until around 2029, when third owners begin treating their aerospace-inspired thoroughbreds like dray horses.

5 reasons why GM is cutting jobs, closing plants in a healthy economy

DETROIT — Even though unemployment is low, the economy is growing and U.S. auto sales are near historic highs, General Motors is cutting thousands of jobs in a major restructuring aimed at generating cash to spend on innovation. It's the new reality for automakers that are faced with the present cost of designing gas-powered cars and trucks that appeal to buyers now while at the same time preparing for a future world of electric and autonomous vehicles. GM announced Monday that it will cut as many as 14,000 workers in North America and put five plants up for possible closure as it abandons many of its car models and restructures to focus more on autonomous and electric vehicles. The reductions could amount to as much as 8 percent of GM's global workforce of 180,000 employees. The cuts mark GM's first major downsizing since shedding thousands of jobs in the Great Recession. The company also said it will stop operating two additional factories outside North America by the end of next year. The move to make GM get leaner before the next downturn likely will be followed by Ford Motor Co., which also has struggled to keep one foot in the present and another in an ambiguous future of new mobility. Ford has been slower to react, but says it will lay off an unspecified number of white-collar workers as it exits much of the car market in favor of trucks and SUVs, some of them powered by batteries. Here's a rundown of the reasons behind the cuts: Coding, not combustion CEO Mary Barra said as cars and trucks become more complex, GM will need more computer coders but fewer engineers who work on internal combustion engines. "The vehicle has become much more software-oriented" with millions of lines of code, she said. "We still need many technical resources in the company." Shedding sedans The restructuring also reflects changing North American auto markets as manufacturers continue to shift away from cars toward SUVs and trucks. In October, almost 65 percent of new vehicles sold in the U.S. were trucks or SUVs. That figure was about 50 percent cars just five years ago. GM is shedding cars largely because it doesn't make money on them, Citi analyst Itay Michaeli wrote in a note to investors. "We estimate sedans operate at a significant loss, hence the need for classic restructuring," he wrote. The reduction includes about 8,000 white-collar employees, or 15 percent of GM's North American white-collar workforce. Some will take buyouts while others will be laid off.