2013 Gmc Terrain Sle-2 on 2040-cars

Auto blog

GM trucks get hybrid versions, but you'll probably never see one

A few years ago, General Motors sold hybrid versions of its Chevy Silverado and GMC Sierra pickups. They weren't very good, using GM's old two-mode hybrid system that resulted in only negligible fuel economy gains. But GM's trying again, launching eAssist models of the 2016 Silverado and Sierra that are said to offer 2-mpg improvements in city, highway, and combined fuel economy ratings. Problem is, you probably won't be able to get one. Only 700 eAssist trucks will be made for the 2016 model year – 500 Silverados and 200 Sierras. When you consider that GM moved 824,683 examples of its light-duty pickups in 2015, this small run represents 0.08-percent of all Silverado/Sierra production, and GM says it "will monitor the market closely ... and adjust as appropriate moving forward." But that's not the only limitation. The eAssist trucks will only be sold through California dealers. For the Silverado, eAssist can only be optioned on the 1500 Crew Cab 1LT 2WD model, and for the Sierra, the fuel-saving technology is solely available on the 1500 SLT Crew Cab 2WD model with the SLT Premium Plus package. Granted, in terms of the Sierra, that means you get niceties like LED headlights and taillights, Apple CarPlay and Android Auto, Bose premium audio, heated seats and steering wheel, lane keep assist, and more. In the trucks, eAssist combines a small electric motor and 0.45-kWh battery pack with the pickups' 5.3-liter V8. GM estimates total output of 355 horsepower and 383 pound-feet of torque – no more horsepower than the non-eAssist trucks, but three more pound-feet of torque. GM says the eAssist trucks can tow up to 9,400 pounds, and the battery only adds 100 pounds to the trucks' weight. The electric motor provides 13 hp and 44 lb-ft of torque for a boost of acceleration off the line, or during passing. It also allows the engine to run in four-cylinder mode for longer periods of time. eAssist uses regenerative braking to help power onboard electrical systems, and adds start/stop to the powertrain. Finally, the so-equipped trucks have a six-percent improvement in aerodynamics, thanks to a soft tonneau cover and active grille shutters in the front fascia. Great news is, the eAssist option is relatively inexpensive, only costing $500. But good luck getting your hands on one.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

Specialty Vehicle Engineering's 750-horsepower GMC Canyon fully revealed

GMC's celebrated Syclone will turn 30 in early 2021, but nothing suggests the company will mark the occasion by releasing a modern interpretation of the pickup. New Jersey-based tuner Specialty Vehicle Engineering (SVE) is taking the matter into its own hands by building a limited number of GMC Canyon trucks with Hellcat-like power. Although the original Syclone received a turbocharged V6, the 2021 model gains a 5.3-liter V8 normally found in bigger vehicles, including the Sierra and Yukon. SVE rebuilt it with forged aluminum pistons, forged steel connecting rods, high-lift valve springs, a custom crankshaft and upgraded fuel injectors among other aftermarket parts. It also added a supercharger to raise the eight's output to 750 horsepower and 600 pound-feet of torque. Power flows to the four wheels via a strengthened 8-speed automatic transmission and a permanent all-wheel-drive system. For context, the first Syclone gave the Chevrolet Corvette a run for its money with a fuel-injected, 4.3-liter V6 turbocharged to 280 horsepower and 360 pound-feet of torque. These numbers were spectacular in the early 1990s since the Sonoma that Syclone was based on shipped with the 105-horse Iron Duke four-cylinder as standard. Even compared with the Sonoma GT that got a naturally aspirated 4.3-liter V6 with 195 horsepower and 260 pound-feet of torque, the Syclone was impressive. SVE installed six-pistons front calipers that clamp 13.6-inch slotted rotors, and it kept the factory brakes out back. It also lowered the suspension by two inches in the front and five inches in the back, upgraded the shocks, and added a heavy-duty rear sway bar. These modifications help drivers make the most of the extra power, but SVE hasn't published performance specifications (like the truck's zero-to-60-mph time) yet. Surprisingly, the eight-cylinder weighs almost the same as the V6 it replaces so the engine swap doesn't affect weight distribution. Visually, the Syclone can't be mistaken for a run-of-the-mill Canyon. It wears a deep front bumper, has cladding over the rocker panels and rides on 20-inch alloys. Edition-specific emblems round out the look, and the list of options includes a body-colored grille as well as a folding tonneau cover. SVE's images show a truck painted black, which was the only color offered on the 1991 model, but it's available in any factory hue. Inside, the modern-day Syclone gains special floor mats and a numbered plaque on the dashboard. Leather is optional.