Slt 4x4 Garage Kept, Pre-owned 44135, Cleveland, Used Cars on 2040-cars

Auto blog

NHTSA upgrades probe into 1.7 million GM vehicles over wiper failures

WASHINGTON — The U.S. National Highway Traffic Safety Administration (NHTSA) said Tuesday it is upgrading an investigation into 1.7 million General Motors vehicles for windshield wiper failures. The auto safety agency opened the probe in November 2018 to see if GM needed to expand a 2016 recall of 2013 model year Chevrolet Equinox and GMC Terrain SUVs to cover additional vehicles. The engineering analysis probe covers 2010-2012 and 2014-2016 Equinox and Terrain vehicles. NHTSA could demand a recall after it completes the probe. NHTSA said it has reviewed 1,900 complaints and reports related to the issue in the 1.7 million vehicles. NHTSA said it has seen elevated failure rates in the 1.7 million vehicles, even though GM said the recalled vehicles have "double the warranty rate and five times the complaint rate." GM said it will "fully cooperate to support their investigation. We do not believe these windshield washer systems are defective." The wiper failures that prompted the 2016 recall were attributed to water and debris intrusion into the windshield wiper assembly ball joints, leading to excessive wear and eventual detachment of the ball joint. GM said it was installing an improved windshield wiper motor and transmission assembly and relocating a drain hole at the base of the windshield. Related Video:

NHTSA, IIHS, and 20 automakers to make auto braking standard by 2022

The National Highway Traffic Safety Administration, the Insurance Institute for Highway Safety and virtually every automaker in the US domestic market have announced a pact to make automatic emergency braking standard by 2022. Here's the full rundown of companies involved: BMW, Fiat Chrysler Automobiles, Ford, General Motors, Honda, Hyundai, Jaguar Land Rover, Kia, Mazda, Mercedes-Benz, Mitsubishi, Nissan, Subaru, Tesla, Toyota, Volkswagen, and Volvo (not to mention the brands that fall under each automaker's respective umbrella). Like we reported yesterday, AEB will be as ubiquitous in the future as traction and stability control are today. But the thing to note here is that this is not a governmental mandate. It's truly an agreement between automakers and the government, a fact that NHTSA claims will lead to widespread adoption three years sooner than a formal rule. That fact in itself should prevent up to 28,000 crashes and 12,000 injuries. The agreement will come into effect in two waves. For the majority of vehicles on the road – those with gross vehicle weights below 8,500 pounds – AEB will need to be standard equipment by September 1, 2022. Vehicles between 8,501 and 10,000 pounds will have an extra three years to offer AEB. "It's an exciting time for vehicle safety. By proactively making emergency braking systems standard equipment on their vehicles, these 20 automakers will help prevent thousands of crashes and save lives," said Secretary of Transportation Anthony Foxx said in an official statement. "It's a win for safety and a win for consumers." Read on for the official press release from NHTSA. Related Video: U.S. DOT and IIHS announce historic commitment of 20 automakers to make automatic emergency braking standard on new vehicles McLEAN, Va. – The U.S. Department of Transportation's National Highway Traffic Safety Administration and the Insurance Institute for Highway Safety announced today a historic commitment by 20 automakers representing more than 99 percent of the U.S. auto market to make automatic emergency braking a standard feature on virtually all new cars no later than NHTSA's 2022 reporting year, which begins Sept 1, 2022. Automakers making the commitment are Audi, BMW, FCA US LLC, Ford, General Motors, Honda, Hyundai, Jaguar Land Rover, Kia, Maserati, Mazda, Mercedes-Benz, Mitsubishi Motors, Nissan, Porsche, Subaru, Tesla Motors Inc., Toyota, Volkswagen and Volvo Car USA.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.