1998 Gmc Jimmy Sls Sport Utility 4-door 4.3l on 2040-cars

Auto blog

GM recalls select Tahoes, Yukons, Escalades for rear driveshaft issue

GM is recalling a number of its full-size SUVs due to an issue with the rear driveshaft assembly that could ultimately result in driveshaft failure. The actual number of total vehicles involved in the recall is small at just 1,789, but it’s spread out across the entire 2021 model year full-size GM vehicle lineup. That means a small number of every model is being recalled, including the Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL and the Cadillac Escalade and Escalade ESV. GM traced the issue back to certain driveshaft assemblies with ball bearings that were not properly heat treated. If theyÂ’re not properly heat treated, GM says that the balls may deform over time, causing noise and vibration. Continue to drive in this condition, and GM says the affected joint in the driveshaft assembly could seize, causing loss of drive power. However, the problem wonÂ’t present itself all at once, as GM says there will be a gradual increase of noises and vibrations before total failure. For those few owners with affected vehicles, GM says that it will replace the left and right rear driveshaft assemblies with properly-built units. Per usual with recalls, this will be done at your local dealership at no cost to the owner. If you have one of the recalled SUVs, expect to be notified mid-March. Related video:

Leak reveals GM's 2017 heavy duty diesel trucks to get 910 lb-ft of torque [UPDATE]

UPDATE: Chevrolet officially announced specs for the 2017 Silverado HD and the rumors were true. The truck's new Duramax 6.6-liter turbo-diesel V8 puts out 445 horsepower and 910 pound-feet of torque. Chevrolet says the new motor produces 19 percent more torque and 12 percent more horsepower, while producing 35 percent fewer emissions. Overall, the new engine is a big improvement over the current motor, which generates 397 horsepower and 765 pound-feet of torque. According to Truck Trend, GM's newest heavy duty pickup trucks will pick up quite a bit more power and torque. The publication spotted a recent GM Powertrain ordering catalog that had the engine specs for the 2017 model year and managed to get some screenshots before the catalog was taken down, and they can be viewed here. The screenshots revealed that the 6.6-liter turbodiesel V8 powering the Silverado and Sierra heavy duty models will boast 445 horsepower and 910 lb-ft of torque. This is a substantial gain over the current models' 397 horsepower and 765 lb-ft of torque, and as Truck Trend points out, it exceeds the Ford Super Duty line's horsepower output of 440, but comes short of the 925 lb-ft rating. Truck Trend credits part of this output gain to the new intake system GM will introduce on the 2017 heavy duties. The intake gets 60 percent of its air from a scoop on the hood, with the other 40 percent coming from behind one of the front fenders. GM doesn't reveal horsepower figures in the press release about the scoop, but it does say the cooler air helps with maintaining the engine's output, and that the scoop does produce a ram-air affect, providing more air at speed. As we know, more air plus more fuel equals more power, but there's likely more to the power increase in this engine than only the intake. Related Video: News Source: Truck Trend via MSN Chevrolet GM GMC Truck Diesel Vehicles

GM Ultium tech can scavenge heat from everywhere, even you

GM likes to give us tidbits about its Ultium platform from time to time, and today it’s telling us about the platformÂ’s ability to capture waste heat from the propulsion system. In addition to capturing from the propulsion system, it can also capture humidity from both inside and outside the vehicle and even from passengersÂ’ body heat. Yes, you, your family and/or your friends are a usable heat source as far as GM EVs are concerned. It then deploys the heat in an advantageous way. If at this point, youÂ’re screaming, "Heat pump!" youÂ’d be right. WeÂ’re talking about an elaborate heat pump system that GM is using for its Ultium-based vehicles. Every Ultium-based GM vehicle gets this system that is covered by 11 patents and four publications. The waste heat it collects is used in a number of ways, but its primary use is to heat the cabin quickly and efficiently. GM claims it can heat the cabin of its Ultium-based vehicles quicker than vehicles with traditional internal combustion engines. Plus, when put to use, GM claims that using the heat pump provides its EVs with up to 10% more range than theyÂ’d have without. Beyond heating the cabin, the heat pump is capable of putting waste heat to use by preheating the battery prior to charging so that you can charge quicker. The system can even cool the propulsion system in preparation for Watts to Freedom (WTF) launch control starts. GM says this was vital in helping the Hummer EV achieve its bonkers 0-60 mph time of about 3 seconds. “Having a ground-up EV architecture gives us the freedom to build in standard features like UltiumÂ’s energy recovery capabilities,” said Doug Parks, GM executive VP of global product development, purchasing and supply chain. “This helps us squeeze more efficiency, performance and overall customer benefit out of our EVs.” GM says itÂ’s been developing heat pump technology since the EV1 and its heat pump. This is the modern evolution of that technology, and GM says itÂ’s going to be implemented in every Ultium-based vehicle as a standard feature. Related video: Green Cadillac Chevrolet GM GMC Technology Electric Future Vehicles