1981 Gmc Caballero on 2040-cars

Auto blog

GM reportedly developing 2.5-liter turbo four-cylinder

General Motors is allocating a massive amount of resources to developing electric technology, but it's not forgetting about the gasoline-powered cars that make up the bulk of its sales. It's reportedly designing a new 2.5-liter turbocharged four-cylinder engine based on its 2.7. Citing "sources familiar with the matter," enthusiast website GM Authority wrote that the 2.5-liter four is "in [the] final stages of development," meaning it should be announced sooner rather than later (assuming the report is accurate). Technical details are few and far between as of writing. The publication learned that the 2.5 will be part of the Cylinder Set Strategy (CSS) family of engines and that it will be mechanically related to the 2.7-liter currently found in the Chevrolet Silverado 1500, among several other models. It will feature dual overhead camshafts. It's too early to tell which models the 2.5-liter four-cylinder will end up in, or how much power it will generate. The output will likely depend on the application. For context, the 2.7 delivers 310 horsepower at 5,600 rpm and 348 pound-feet of torque between 1,500 and 4,000 rpm in the Silverado. In the smaller Colorado, it provides anywhere between 237 and 310 horsepower depending on the trim level selected. While this is pure speculation, our crystal ball tells us the engine will end up powering crossovers. It's an easy deduction to make. We can't imagine it will be offered in the Silverado, and seeing it in the Colorado is unlikely because its entry-level engine develops 237 horsepower; there's likely not much of a market for a midsize truck with 200 or so horsepower. Putting it in the Corvette wouldn't make sense and the Camaro has nearly reached the end of its life cycle without a successor planned. This leaves us with Chevrolet's range of crossovers, like the Equinox, as well as their GMC-, Buick-, and Cadillac-branded counterparts. We're not discounting the possibility that the cars set to receive the 2.5 haven't been unveiled, but those are likely crossovers, too; the odds of seeing another big Chevy sedan are very, very low. General Motors hasn't commented on the report, and it hasn't publicly announced plans to expand its CSS family of engines. If the report is accurate, we should learn more about the new turbocharged, 2.5-liter four-cylinder engine in the not-too-distant future. Featured Gallery 2022 Chevrolet Equinox RS View 56 Photos Buick Chevrolet GM GMC

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

GM is the latest automaker accused of diesel emissions cheating

Volkswagen and Ram need to make room on the diesel-emissions bench for General Motors. America's largest automaker was accused in a lawsuit on Thursday of rigging hundreds of thousands of diesel trucks with at least three so-called defeat devices to ensure that the trucks would meet federal and state emission standards, even if they generated more pollution in real-world driving. According to the complaint, on-road emissions testing conducted for the plaintiffs found that Duramax-equipped trucks produced NOx pollutants, comprised of nitrogen and oxygen atoms, two to five times higher than legally permitted, and "many times" higher than their gasoline counterparts. The proposed class-action lawsuit was filed in federal court in Detroit on behalf of people who own or lease more than 705,000 Chevrolet Silverado and GMC Sierra pickup trucks fitted with "Duramax" engines from 2011 to 2016 model years. The lawsuit seeks remedies including possible refunds or restitution for lost vehicle value, plus punitive damages. It adds to legal problems for Detroit-based GM, which has already paid about $2.5 billion in penalties and settlements over faulty ignition switches linked to 124 deaths. GM joins at least five automakers whose diesel emissions have been scrutinized by regulators or consumers. They include VW, which has admitted to cheating; Mercedes-Benz parent Daimler; Fiat Chrysler Automobiles, Peugeot and Renault. GM spokesman Dan Flores called the claims "baseless," and said the trucks comply with US Environmental Protection Agency emissions standards and California's own tough standards. Shares of GM were down 69 cents, or 2.1 percent, at $32.50 in afternoon trading, after earlier falling to $31.93. The GM lawsuit was filed by several law firms, including Hagens Berman Sobol Shapiro, which helped reach multibillion-dollar settlements with VW on behalf of drivers and dealers. The case is Fenner et al v General Motors LLC et al, US District Court, Eastern District of Michigan, No. 17-11661. The named plaintiffs are Andrei Fenner of Mountain View, California and Joshua Herman of Sulphur, Louisiana. They said they would not have bought their respective 2011 Sierra and 2016 Silverado trucks, or would have paid less for them, had they known about the alleged rigging. Joseph Spak, an RBC Capital Markets analyst, in a research report said "negative publicity" from the lawsuit could drive buyers to trucks from Ford or even Fiat Chrysler's Ram.