Mustang Boss 302 Pro Touring 302/525 Hp V8 5 Speed 4.30 on 2040-cars

Auto blog

2016 Ford Shelby GT350 Mustang rated at 526 hp, 429 lb-ft

When Ford debuted the Shelby GT350 Mustang at the LA Auto Show last year, we were told it'd have more than 500 horsepower and over 400 pound-feet of torque. And indeed it does; Ford confirmed today that its hot 'Stang will make 526 hp at 7,500 rpm and 429 lb-ft at 4,750 rpm. Compared to the GT350's main rival, the Chevy Camaro Z/28, that's an increase of 21 hp, but a loss of 52 lb-ft. That said, this Mustang packs some serious prowess, especially in its most hardcore GT350R trim. It sounds pretty wicked, too. It's worth noting that both the standard GT350 and GT350R use the same engine, with the same output ratings. It's also worth noting that this is a flat-plane-crank engine. It's the most powerful naturally aspirated engine Ford has ever made, with 102 hp per liter. Redline is 8,250 rpm. It's a lightweight engine, too – the 5.2-liter mill weighs less than Ford's own 5.0-liter Coyote V8. Perhaps most impressive is the price point for the 2016 Shelby GT350. The standard car comes in at $47,870, while the GT350R will command $61,370 – a big drop over the Camaro Z/28 and it's $73,300 sticker price (including destination but not gas guzzler charges). Ford confirmed the power output news at a media briefing today near its headquarters in Dearborn, MI. Stay tuned for more information as it becomes available. Related Video:

Ford recalls 600,000 older-model sedans for braking issue

Ford is recalling 600,166 older-model Ford, Lincoln and Mercury vehicles over an issue that could affect braking and increase the risk of a crash. The safety recall covers certain Ford Fusion, Mercury Milan and Lincoln MKZ sedans from the 2006 through 2010 model years that were built at Ford’s Hermosillo Assembly Plant in Mexico between Feb. 22, 2006, and July 15, 2009. Ford says a valve that is normally closed inside the hydraulic control unit may get stuck in the open position or be slow to close, which could make it harder to engage the brakes and increase risk of a crash. Ford says itÂ’s aware of 15 reports of accidents and two injuries possibly related to the issue. Dealers will inspect the hydraulic control unit for signs of the problem and replace it, if necessary. The dealers will pressure-flush the system with brake fluid and replace the reservoir cap with a new one. Ford is also issuing a small recall of 33 of its 2020 F-150 trucks in the U.S. and 51 in Canada over potentially damaged spare tires. It says the bead area on the tires may have been damaged when it was mounted onto the wheel assembly, leaving it vulnerable to corrosion, separation of the bead wire and ultimately a rapid loss of air pressure and detachment from the wheel. Dealers will replace the spare tire. Affected vehicles were built at the Dearborn Truck Plant from Nov. 10-21 of this year.

Why Edmunds took a sledgehammer to its 2015 Ford F-150

The discussion around repair bills for the aluminum-bodied 2015 Ford F-150 pickup continued from the beginning of last year to the end, and haven't abated; as an aside, some Tesla Model S owners have been shocked at disquieting repair estimates for minor damage to their aluminum wunder-sedans. Edmunds decided to inject some fact into the fray: it bought a $52,000 long-term 2015 F-150 and clouted it with an eight-pound sledgehammer. Twice. The rear of the bedside took the impacts since it couldn't be replaced, it would have to be repaired. To the pickup's credit, the only reason associate editor Travis Langness hit it twice was that the first sledgehammer blow didn't do as much damage as Edmunds wanted. After the second, the visible damage included the two direct impacts, a few creases, and a cracked taillight, so they drove the pickup to Santa Monica Ford to get an estimate, complete with a fictitious story about how the damage occurred and the mercy plea that Langness was paying for the repair out-of-pocket. In Part 2 Langness hits on some of the details with getting the truck fixed, such as the massively expensive taillight and the list of tools Ford recommends dealers have to work on aluminum. But he was promised he'd have his truck back in seven days, and Santa Monica Ford got it back to him in seven days. In Part 3 we get the bill. It's not small, but it's quite a bit less than it could have been if the service manager had charged Edmunds the official labor rate for aluminum. We're not going to spoil it here, so check out the videos above and below for the beginning and the end, and head over to Edmunds for the complete story about how it all happened and some riffing on the repair numbers. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Related Video: